Bedienungsanleitung Makita AR410HR (Seite 10 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598404

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

1. Disconnect air hose.

2. Press down lever while opening door. (Fig. 9)

3. Open magazine cap. (Fig. 10)

4. Load screws into magazine.

5. Pull out lead screw as far as driver guide and then

close magazine cap.

6. Completely load lead screw into screw channel. At this

point, check to see that screw is completely set in

feeding claw.At this time, if the screw cannot be set

because the bit has come down as far as the driver

guide, turn the main unit upside down (driver guide is

on top), and return the bit to its designated position.

7. Slowly close door until lever stops fully. (Fig. 11)

OPERATION

How to Drive Screws

CAUTION:

• The utilized air pressure must be between 1.76 and

2.26 MPa. Do not repeatedly drive screw(s) in on top of

a screw that has been already driven in.

• This driver is not an impact gun, so it requires a

reasonable amount of pressing.

• If the main unit is not pressed sufficiently, the screw

may not drive in flush to workpiece, or come out.

• Always press the end of the discharge nose at a right

angle onto the workpiece and then drive in screw. We

recommend that you use the intermitent-drive action to

ensure proper screw driving. (Fig. 12 & 13)

First, lightly press the end of the contact arm onto a

workpiece.

Next, pull the trigger.Here, do not release the trigger until

the motor stops running.Note that if the trigger is released

too soon, the screw may not be driven in flush to

workpiece, and/or the screw feed may be impaired.

Switching between intermitent drive and

continuous drive

Intermitent Drive Method (Fig. 14 & 15)

Intermitent drive is where the contact arm is pressed

against a workpiece, and the trigger pulled to drive in one

screw.

Set the switching lever to the position to set driver to

“Intermitent Drive Mode”.

(1) Press contact arm against workpiece.

(2) Pull trigger.

Continuous Drive Method (Fig. 16 & 17)

Continuous drive is where the contact arm is repeatedly

pressed onto different areas of workpiece while the trigger

is held down to continuously drive in screws.

Set the switching lever to the position to set driver to

“Continuos Drive Mode”.

(1) Pull trigger.

(2) With the trigger held down, each time the contact

arm is pressed against the workpiece, a screw

will be driven in continuously.

Trigger Locking Method

This driver has a trigger lock to prevent accidents due to

mistaken operation when main unit is not being used.

The trigger lock is a mechanism that locks the trigger,

preventing discharge of screws.

Set the switching lever to the position to set driver to

“Trigger Lock”.

When drive screws, set lock lever to the position or

position. When not using the driver, always lock the

trigger and disconnect the air hose.

How to Cut linked Sheet (Fig. 18)

CAUTION:

• When cutting linked sheet, always lock trigger, and

disconnect air hose.

When using linked screws, the linked sheet protrudes

from the driver guide. Tear away the protruding linked

sheet in the direction of the arrow.

MAINTENANCE

CAUTION:

• Always disconnect the air hose from the tool before

attempting to perform inspection or maintenance.

How to Rectify Screw Jam

CAUTION:

• When rectifying screw jam, always lock trigger, and

disconnect air hose. (Fig. 19)

Lock trigger and disconnect air hose.

Open door, and pull out linked screws.

Insert thin metal bar into discharge nose, and hit it with a

hammer. In some cases, this metal bar will become stuck

when hit. Note, that at such times, the bit must not be hit,

as the bit end may be damaged, and lead to impaired

screw driving. (Fig. 20)

Remove screw(s) jammed inside driver guide using minus

screwdriver or other such tool.

After removing screw(s), make sure bit is not protruding

into screw channel (if it is, press it out of the way using the

metal bar).

After removing the jammed screw(s), reload the driver

with screws.

How to Replace Bit

CAUTION:

• When replacing bit, always lock trigger, disconnect air

hose, and remove all loaded screws.

Take care not to lose small components.

Replace bit in clean surroundings to prevent dust and dirt

from getting onto internal components.

Removing Bit (Fig. 21)

1. Disconnect hose and remove all loaded screws.

2. Use hex wrench to loosen the four hex bolts, and then

remove top cap.

- The top cap spacer is removable, but please leave it

on the driver.

- If top cap gasket is removed with top cap, be careful

not to misshapen it, and be sure to put it back when

reassembling.

3. Insert the hex wrench into the bit channel of the driver

guide, and push out the piston assembly. (Fig. 22)

4. Use an eyeleteer, etc., to remove rubber ring (white)

from unloaded piston assembly.

- As the new bit comes with a white rubber ring, the

old one can be cut out with a cutter knife, etc. if it is

difficult to remove. (Fig. 23 & 24)

5. Next, extract pin from piston assembly. (Fig. 25)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AR410HR Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info