Bedienungsanleitung Makita BUM168 (Seite 14 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600689

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Fit the crank with its recessed part facing upwards onto

the pins. At this time, apply a small amount of grease to

the periphery of the crank using grease that the shear

blades as optional accessory are provided with or that

remains inside gear housing. (Fig. 17)

Overlap the oval hole in the upper blade with that in the

lower one. Move the shear blades so that the hole in the

base plate of shear blades are positioned in the center of

these overlapped oval holes. (Fig. 18)

Turn the shear blades upside down and install it so that

the pins on the tool fit in the hole in the shear blades.

Make sure that the shear blades are set in place securely

as far as they reach the base plate. (Fig. 19)

Place the undercover so that the symbol on the

undercover is aligned with the symbol Δ on the locking

lever. (Fig. 20)

Press the undercover down and turn the undercover

clockwise while pressing it down until the symbol on

the label is aligned with the symbol Δ on the locking lever

(the undercover is completely locked.). (Fig. 21)

At this time, make sure that the locking lever fits in the

groove in the undercover.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades do not operate properly, there

is a poor fit between the blades and crank. Redo from

the beginning.

OPERATION

WARNING:

• Keep hands away from blades.

CAUTION:

• Smear the blade before and once per hour during

operation using machine oil or the like.

• Avoid operating the tool under the scorching sunlight

as much as practicable. When operating the tool, be

careful of your physical conditions.

• Hold the tool with one hand. Do not hold the front bulge

of the tool as a grip. (Fig. 22)

Turn the tool on after adjusting the shearing height and

hold it so that the foot of the tool rest on the ground. Then

gently move the tool forward into the area to be cut.

(Fig. 23)

When trimming around curb, fence or trees, move the tool

along them. Be careful for the blade not to contact them.

(Fig. 24)

When trimming sprouts or foliage of a small tree, remove

the base frame from the tool and cut little by little.

Shear big branches to your desired height beforehand

using branch scissors before using this tool.

CAUTION:

• When trimming twigs and foliage, do not attempt to trim

too much at a time. Proceed gently. Also do not

attempt to cut thick branches.

• Do not let the shear blades contact the grounds during

operation. The blades will be dulled, causing poor

performance.

• Do not trim wet grass or foliage of small trees.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Shear blade maintenance (Fig. 25 & 26)

After operation, remove dust from both sides of the blade

with wired brush, wipe off it with a rag and then apply

enough low-viscosity oil, such as machine oil etc. and

spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so may

cause rust or damage on the tool.

• Dirt and corrosion cause excessive blade friction and

shorten the operating time per battery charge.

After use

• To clean off the exterior of the tool, dampen a soft cloth

in a soapy water and wipe gently. Never use thinner or

benzine.

• Do not store the tool in a place where volatile materials

are stored.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Grass shear blade assembly

• Grass shear blade cover

• Base frame

• Makita genuine battery and charger

• Long handle attachment

For cordless hedge trimmer use

This tool can be used as a hedge trimmer by using the

hedge shear blade (optional accessory) and 2-way

change set (optional accessory).

To use this tool as a hedge trimmer, replacing the grass

shear blades with the hedge shear blades is required.

For removing the grass shear blades, refer to the

aforementioned section titled “Installing or removing grass

shear blades”. For installing the hedge shear blades, refer

to the section below titled “Installing or removing hedge

shear blades”.

• Hedge shear blade assembly (for Hedge Trimmer)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BUM168 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info