Bedienungsanleitung Makita BUM168 (Seite 16 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600689

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

As a basic operation, tilt the blades towards the trimming

direction and move it calmly and slowly at the speed rate

of 3 - 4 seconds per meter. (Fig. 44)

To cut a hedge top evenly, it helps to tie a string at the

desired hedge height and to trim along it, using it as a

reference line. (Fig. 45)

Attaching the chip receiver (optional accessory) on the

tool when trimming the hedge straight can avoid cut off

leaves’ being thrown away. (Fig. 46)

To cut a hedge side evenly, it helps to cut from the bottom

upwards. (Fig. 47)

Trim boxwood or rhododendron from the base toward the

top for a nice appearance and good job.

Installing or removing chip receiver

(optional accessory)

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing chip receiver.

NOTE:

• When replacing the chip receiver, always wear gloves

so that hands and face does not directly contact the

blade. Failure to do so may cause personal injury.

• When replacing the chip receiver, always be careful not

to contact the shear blades.

• The chip receiver receives cut-off leaves and alleviates

collecting thrown-away leaves. This can be installed on

either side of the tool. (Fig. 48)

Place the chip receiver on the shear blades so that its slits

overlap with the screws on the shear blades and secure it

using two clamping nuts.

To remove the chip receiver, loosen and remove the two

clamping nuts and then take it out.

Storage (Fig. 49)

The hook hole in the tool bottom is convenient for hanging

the tool from a nail or screw on the wall.

Put the blade cover on the shear blades so that the blades

are not exposed. Store the tool out of the reach of children

carefully.

Store the tool in the place not exposed to water and rain.

Noise

ENG905-1

The typical A-weighted noise level determined according

to IEC60335:

Model BUM166

Sound pressure level (L

): 77 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Model BUM168

Sound pressure level (L

): 78 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to IEC60335:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Hedge trimming operation with optional hedge shear

blades

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 74 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH003-14

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Cordless Grass Shear

Model No./ Type: BUM166, BUM168

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745, EN60335

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BUM168 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info