Bedienungsanleitung Makita DTR181 (Seite 20 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793624

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

20 ENGLISH

• If you are repeating the wire tying processes in



from the switch trigger. Then, continue to operate

the switch trigger.

• If you pull the switch trigger when there is no tie

wire left, an error is displayed. Replace with a new

tie wire and restart the tool.

Tying tips

• Tilt the tool at a 45° angle against the crossed

rebars, and tie the wire in alternate orientations as



Fig.41

 

sections of crossed rebars.

Fig.42

 󰀩

orientation and perform tying twice so that tying

strength increases.

Fig.43

NOTICE: When you make the second tie, bend



tie. Otherwise, the wire may be repelled a second

time. It may cling to the tool tip, and the hook may be

damaged.

Replacing the tie wires

CAUTION: When you replace the wire, be sure

󰀨

the battery cartridge. Failure to do so may cause an

accident.

1. When wire has been used up, an error tone will

sound and error "1" will be displayed.

2. 󰀨

the battery cartridge.

3. Push the release lever, and lock it with the lock

lever.

Fig.44: 1. Release lever 2. Lock lever

4. Remove the wire reel from the tool.

NOTE: When wire has been used up normally,

approximately 20 cm of the wire remains wound on

the reel. In this state, replace the wire reel with a new

one.

󰀩

follow the steps below.

1. Insert the battery cartridge into the tool, and

turn the power on. The tool feeds the wire and cuts it

automatically.

2. 󰀨

the battery cartridge.

3. Remove the wire breaks using tools such as nip-

pers or pliers.

MAINTENANCE

CAUTION: Always be sure that the tool is

󰀨

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,



be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Cleaning the cutter section

When the tool is used, dust and wire particles may

become adhered to the cutter section. In such a case,

clean the cutter section according to the following pro-

cedure. The cleaning should be done each time you use

up a box of reel. (50 pcs.)

Using the wire brush

1. Open the reel cover.

Fig.45: 1. Reel cover

2. Push the release lever, and lock it with the lock

lever.

Fig.46: 1. Release lever 2. Lock lever

3. Pass the wire brush through the guide.

When inserting the wire brush, hold it short and push it

into the guide little by little.

Fig.47: 1. Wire brush

Fig.48: 1. Gear 2. Guide 3. Wire brush

4. Push in the wire brush until its top end comes out

from the tip of the arm. And then pull out the wire brush.

This action is enough with one time.

Fig.49: 1. Arm 2. Wire brush

5. Close the reel cover.

Fig.50: 1. Reel cover

Using the air duster gun

Open the reel cover, push the release lever, and lock it

with the lock lever. Then bring the air duster gun close

to the guide and blow the air. Make sure the air comes

from the tip of the arm.

Fig.51: 1. Air duster gun 2. Guide

Cleaning with disassembly

If the cutter section is clogged or a wire is caught in it,

disassemble the parts and clean them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTR181 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info