793624
19
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
19 ENGLISH
Checking the trigger-lock
The tool has the trigger-lock to prevent the tool from
operating when you do not intend to use it. Lock the trig-

Checking the curl guide
To prevent the operator from touching the binding or
rotating parts of the tool tip by mistake, the tool will not
operate even if the switch trigger is pulled while the
curl guide is opened. When the operator releases their

the tool can operate.
Fig.31: 1. Curl guide
Checkout for curl guide open/close
detection
Remove the tie wire, check the tool operation according
to the following steps, and make sure that the tool does
not start if the curl guide is open.
1. 󰀨
2. Turn the power on.
If the tool will not operate and if the value "2" is shown
on the display panel, the state of the tool is normal. Turn
󰀨
If the tool operates and if no error is shown on the dis-
play panel, the state of the tool is abnormal. Stop using
the tool immediately, and ask your local Makita Service
Center for repairs.
CAUTION: If you open the curl guide and turn
the power on to check the interlock, hold the curl

limbs or face close to the binding or rotating parts
of the tool tip.
Fig.32
Tying work
CAUTION: Before inserting the battery car-

switch trigger and lock the trigger. If you insert
the battery cartridge while the switch trigger is being
pulled, it may cause an accident if the wire tying
process is accidentally carried out.
CAUTION: When you turn the power on, never
bring your limbs or face close to the binding or
rotating parts of the tool tip. Otherwise, you may

CAUTION: When the power is turned on,
never touch the binding or rotating parts of the
tool tip.
Fig.33
Preparation before work
1. Make sure that the battery cartridge is removed
and the trigger is locked.
2. Insert the battery cartridge into the tool, and turn
the power on. When you turn the power on, the wire is
cut automatically.
NOTICE: Make sure that the tying mode lamp
lights up when the power is turned on. If it does
not light up, recharge the battery.
3. Release the trigger lock.
Fig.34: 1. Trigger-lock button 2. Switch trigger
3. Power button 4. Tying mode lamp
Single actuation mode
1. 
sure to place the tool vertically over the rebars and
press the arm on the tying point at a 45° angle against
the crossed rebars.
Fig.35: 1. Arm
2. Pull the switch trigger once.
3. The wire is fed and cut automatically.
4. The hook holds and twists the wire, then returns to
the original position after the wires have been tied.
5. After tying, be careful not to hook the arm on the
rebars, and then pull the tool up.
Fig.36
CAUTION: If the wire has clung to the binding
󰀨
Lock the trigger, remove the battery cartridge,
and remove the wire using tools such as nippers
or pliers.
Fig.37
Continuous actuation mode
1. Switch the tool mode from the single actuation
mode to the continuous actuation mode using the mode
switching button.
Fig.38: 1. Mode switching button
2. Release the trigger lock.
3. While pulling the switch trigger, push the tool
vertically against the rebars, and press the arm against
the point where the rebars cross at a 45-degree angle.

The wire will be tied.
Fig.39: 1. Contact plate
4. After tying, be careful not to hook the arm on the
rebars, and then pull the tool up.
Fig.40
Cautions on working
If you move the arm from the tying position during
the wire tying process, the wire will get stuck on
the hook, which may lead to incorrect tying.
Keep pressing the tool against the rebars until the
wire tying process is completed.
Do not move to the next tying point until the cur-
rent wire tying process is completed.
The tool tip rotating part (hook) twists the wire

so that your body is not pulled by the tool.
Do not touch the wires during the wire tying
process.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita DTR181 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info