Bedienungsanleitung Makita GF600 (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599698

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

– when changing one driving location to another

involves the use of scaffoldings, stairs, ladders, or

ladder alike constructions, e.g. roof laths;

– closing boxes or crates;

– fitting transportation safety systems e.g. on vehicles

and wagons.

• Check walls, ceilings, floors, roofing and the like

carefully to avoid possible electrical shock, gas

leakage, explosions, etc. caused by striking live wires,

conduits or gas pipes.

• Do not use the tool for fastening electrical cables. It is

not designed for electric cable installation and may

damage the insulation of electric cables thereby

causing electric shock or fire hazards.

• Watch your footing and maintain your balance with the

tool. Make sure there is no one below when working in

high locations to prevent danger if there is sudden

jerking or catching.

• On rooftops and other high locations, drive fasteners

as you move forward. It is easy to lose your footing if

you drive fasteners while inching backward. When

driving fasteners against perpendicular surface, work

from the top to the bottom. You can perform driving

operations with less fatigue by doing so.

• A fastener will be bent or the tool can become jammed

if you mistakenly drive fastener on top of another

fastener or strike a knot in the wood. The fastener may

be thrown and hit someone, or the tool itself can react

dangerously. Place the fasteners with care.

• Never attempt to drive fasteners from both the inside

and outside at the same time. Fasteners may rip

through and/or fly off, presenting a grave danger.

Service

• Perform cleaning and maintenance right after finishing

the job. Keep the tool in tip-top condition. Lubricate

moving parts to prevent rusting and minimize friction-

related wear. Wipe off all dust from the parts.

• Ask Makita authorized service center for periodical

inspection of the tool.

• To maintain product SAFETY and RELIABILITY,

maintenance and repairs should be performed by

Makita Authorized Service Centers, always using

Makita replacement parts.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

IMPORTANT SAFETY

INSTRUCTIONS ENC009-1

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

Overview of the nailer (Fig. 2)

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure to remove the fuel cell, the battery

cartridge and nails before adjusting or checking

function on the tool.

Installing or removing battery cartridge

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury. (Fig. 3)

To install the battery cartridge, hold it so that the battery

cartridge front shape fits to that of the battery installment

opening and slip it into place. Insert it all the way until it

locks in place with a little click. (Fig. 4)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GF600 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info