Bedienungsanleitung Makita HS6601 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691840

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

8 ENGLISH

damagedparts,gummydeposits,orabuild-upof

debris.

3. Lower guard may be retracted manually only

for special cuts such as “plunge cuts” and

“compound cuts”. Raise lower guard by

retracting handle and as soon as blade enters

the material, the lower guard must be released.

For all other sawing, the lower guard should oper-

ate automatically.

4. Always observe that the lower guard is cov-

ering the blade before placing saw down on

bench or oor.Anunprotected,coastingblade

willcausethesawtowalkbackwards,cutting

whatever is in its path. Be aware of the time it

takesforthebladetostopafterswitchisreleased.

5. To check lower guard, open lower guard by

hand, then release and watch guard closure.

Also check to see that retracting handle does

not touch tool housing.Leavingbladeexposed

isVERYDANGEROUSandcanleadtoserious

personalinjury.

Additional safety warnings

1. Use extra caution when cutting damp wood,

pressure treated lumber, or wood containing

knots. Maintain smooth advancement of tool with-

outdecreaseinbladespeedtoavoidoverheating

thebladetips.

2. Do not attempt to remove cut material when

blade is moving. Wait until blade stops before

grasping cut material. Blades coast after turn off.

3. Avoid cutting nails. Inspect for and remove all

nails from lumber before cutting.

4. Place the wider portion of the saw base on

that part of the workpiece which is solidly

supported, not on the section that will fall off

when the cut is made. If the workpiece is short

or small, clamp it down. DO NOT TRY TO HOLD

SHORT PIECES BY HAND!

►Fig.5

5. Before setting the tool down after completing a

cut, be sure that the guard has closed and the

blade has come to a complete stop.

6. Never attempt to saw with the circular saw

held upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

►Fig.6

7. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

8. Do not stop the blades by lateral pressure on

the saw blade.

9. Do not use any abrasive wheels.

10. Only use the saw blade with the diameter that

is marked on the tool or specied in the man-

ual.Useofanincorrectlysizedblademayaffect

theproperguardingofthebladeorguardopera-

tionwhichcouldresultinseriouspersonalinjury.

11. Keep blade sharp and clean.Gumandwood

pitchhardenedonbladesslowssawand

increasespotentialforkickback.Keepbladeclean

byrstremovingitfromtool,thencleaningitwith

gum and pitch remover, hot water or kerosene.

Never use gasoline.

12. Wear a dust mask and hearing protection when

use the tool.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Adjusting depth of cut

CAUTION: After adjusting the depth of cut,

always tighten the lever securely.

►Fig.7: 1. Lever

Loosentheleveronthedepthguideandmovethebase

upordown.Atthedesireddepthofcut,securethebase

bytighteningthelever.

For cleaner, safer cuts, set cut depth so that no more

thanonebladetoothprojectsbelowworkpiece.Using

proper cut depth helps to reduce potential for danger-

ousKICKBACKSwhichcancausepersonalinjury.

Bevel cutting

►Fig.8: 1. Clamping screw 2. Bevel scale plate

►Fig.9: 1. Clamping screw

Loosen the clamping screws. Set for the desired angle

(0°-45°)bytiltingaccordingly,thentightentheclamp-

ing screws securely.

Sighting

►Fig.10: 1. Cutting line (0° position) 2. Cutting line

(45° position)

For straight cuts, align the 0° position on the front of the

basewithyourcuttingline.For45°bevelcuts,alignthe

45° position with it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HS6601 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info