Bedienungsanleitung Makita HS6601 (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691840

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

9 ENGLISH

Switch action

WARNING: Before plugging in the tool,

always check to see that the switch trigger actu-

ates properly and returns to the "OFF" position

when released.

WARNING: NEVER defeat the lock-off button

by taping down or some other means. A switch with

anegatedlock-offbuttonmayresultinunintentional

operationandseriouspersonalinjury.

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press-

ing the lock-off button. A switch in need of repair

may result in unintentional operation and serious

personalinjury.ReturntooltoaMakitaservicecenter

forproperrepairsBEFOREfurtherusage.

►Fig.11: 1. Switch trigger 2.Lock-offbutton

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-offbuttonisprovided.Tostartthetool,

depressthelock-offbuttonandpulltheswitchtrigger.

Releasetheswitchtriggertostop.

NOTICE: Do not pull the switch trigger hard

without pressing in the lock-off button. This can

causeswitchbreakage.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Removing or installing circular saw

blade

CAUTION: Be sure the circular saw blade is

installed with teeth pointing up at the front of the

tool.

CAUTION: Use only the Makita wrench to

install or remove the circular saw blade.

Toremovethecircularsawblade,presstheshaftlock

fullysothatthecircularsawbladecannotrevolveand

usethewrenchtoloosenthehexboltcounterclockwise.

Thenremovethehexbolt,ring(countryspecic),outer

angeandcircularsawblade.

►Fig.12: 1. Hex wrench 2. Shaft lock 3. Loosen

4. Tighten

For tool without the ring

►Fig.13: 1.Hexbolt2.Outerange3. Circular saw

blade4.Innerange

For tool with the ring

►Fig.14: 1.Hexbolt2.Outerange3. Circular saw

blade4.Ring5.Innerange

Toinstallthecircularsawblade,followtheremoval

procedure in reverse.

For tool with the inner ange for

other than 15.88 mm hole-diameter

saw blade

Theinnerangehasacertaindiameterprotrusionon

one side of it and a different diameter protrusion on the

other side. Choose a correct side on which protrusion

tsintothesawbladeholeperfectly.Mounttheinner

angeontothemountingshaftsothatthecorrectside

ofprotrusionontheinnerangefacesoutwardandthen

placesawbladeandouterange.

►Fig.15: 1. Mounting shaft 2.Innerange3. Circular

sawblade4.Outerange5.Hexbolt

WARNING: BE SURE TO TIGHTEN THE HEX

BOLT CLOCKWISE SECURELY. Also be careful

not to tighten the bolt forcibly. Slipping your hand

from the hex wrench can cause a personal injury.

WARNING: Make sure that the protrusion "a"

on the inner ange that is positioned outside ts

into the saw blade hole "a" perfectly. Mounting the

bladeonthewrongsidecanresultinthedangerous

vibration.

For tool with the inner ange for a

15.88 mm hole-diameter saw blade

(country specic)

Mounttheinnerangewithitsrecessedsidefacing

outward onto the mounting shaft and then place saw

blade(withtheringattachedifneeded),outerange

andhexbolt.

For tool without the ring

►Fig.16: 1. Mounting shaft 2.Innerange3. Circular

sawblade4.Outerange5.Hexbolt

For tool with the ring

►Fig.17: 1. Mounting shaft 2.Innerange3. Circular

sawblade4.Outerange5.Hexbolt

6.Ring

WARNING: BE SURE TO TIGHTEN THE HEX

BOLT CLOCKWISE SECURELY. Also be careful

not to tighten the bolt forcibly. Slipping your hand

from the hex wrench can cause a personal injury.

WARNING: If the ring is needed to mount the

blade onto the spindle, always be sure that the

correct ring for the blade's arbor hole you intend

to use is installed between the inner and the outer

anges.Useoftheincorrectarborholeringmay

resultintheimpropermountingofthebladecausing

blademovementandseverevibrationresultingin

possiblelossofcontrolduringoperationandinseri-

ouspersonalinjury.

Blade guard cleaning

Whenchangingthecircularsawblade,makesureto

alsocleantheupperandlowerbladeguardsofaccu-

mulated sawdust as discussed in the Maintenance

section. Such efforts do not replace the need to check

lowerguardoperationbeforeeachuse.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HS6601 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info