Bedienungsanleitung Makita HS6601 (Seite 10 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691840

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

10 ENGLISH

Hex wrench storage

►Fig.18: 1. Hex wrench

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

Connecting a vacuum cleaner

Optional accessory

When you wish to perform clean cutting operation,

connect a Makita vacuum cleaner to your tool. Connect

a hose of the vacuum cleaner to the dust nozzle as

showninthegure.

►Fig.19: 1. Dust nozzle 2. Screw

►Fig.20: 1. Hose 2. Vacuum cleaner

OPERATION

CAUTION: Be sure to move the tool forward

in a straight line gently. Forcing or twisting the tool

will result in overheating the motor and dangerous

kickback,possiblycausingsevereinjury.

►Fig.21

Holdthetoolrmly.Thetoolisprovidedwithbothafront

gripandrearhandle.Usebothtobestgraspthetool.

Ifbothhandsareholdingsaw,theycannotbecutby

thecircularsawblade.Setthebaseontheworkpiece

tobecutwithoutthecircularsawblademakingany

contact. Then turn the tool on and wait until the circular

sawbladeattainsfullspeed.Nowsimplymovethetool

forwardovertheworkpiecesurface,keepingitatand

advancing smoothly until the sawing is completed.

To get clean cuts, keep your sawing line straight and

your speed of advance uniform. If the cut fails to prop-

erly follow your intended cut line, do not attempt to turn

orforcethetoolbacktothecutline.Doingsomaybind

thecircularsawbladeandleadtodangerouskickback

andpossibleseriousinjury.Releaseswitch,waitforcir-

cularsawbladetostopandthenwithdrawtool.Realign

tool on new cut line, and start cut again. Attempt to

avoid positioning which exposes operator to chips and

wooddustbeingejectedfromsaw.Useeyeprotection

tohelpavoidinjury.

Rip fence (Guide rule)

Optional accessory

►Fig.22: 1.Ripfence(Guiderule)2. Clamping screw

The handy rip fence allows you to do extra-accurate

straight cuts. Simply slide the rip fence up snugly

against the side of the workpiece and secure it in posi-

tionwiththeclampingscrewonthefrontofthebase.It

alsomakesrepeatedcutsofuniformwidthpossible.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

CAUTION: Clean out the guard to ensure

there is no accumulated sawdust and chips

which may impede the operation of the guarding

system. A dirty guarding system may limit the proper

operation which could result in serious personal

injury.Themosteffectivewaytoaccomplishthis

cleaning is with compressed air. If the dust is being

blown out of the guard, be sure the proper eye

and breathing protection is used.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Adjusting the parallelism

►Fig.23: 1. Screw

Thisadjustmenthasbeenmadeatthefactory.Butifitis

off,youcanadjustitasthefollowingprocedure.

1. Make sure all levers and screws are tightened.

Slightly loosen the screw illustrated.

2. While opening the lower guard, move the rear of

thebasesothatthedistanceAandBbecomesequal.

3. Tighten the screws and make a test cut to check

the parallelism.

Adjusting 0°-cut accuracy

►Fig.24: 1.Adjustingbolt

►Fig.25: 1. Triangular rule 2. Clamping screw

Thisadjustmenthasbeenmadeatthefactory.Butifitis

off,youcanadjustitasthefollowingprocedure.

1. Slightly loosen the clamping screws on the front

and rear of the tool.

2. Makethebaseperpendiculartothebladeusing

atriangularruleorsquarerulebyturningtheadjusting

bolt.

3. Tighten the clamping screws and make a test cut

to check the verticalness.

Replacing carbon brushes

►Fig.26: 1. Limit mark

Checkthecarbonbrushesregularly.

Replacethemwhentheyweardowntothelimitmark.

Keepthecarbonbrushescleanandfreetoslipinthe

holders.Bothcarbonbrushesshouldbereplacedatthe

sametime.Useonlyidenticalcarbonbrushes.

1. Useascrewdrivertoremovethebrushholder

caps.

2. Takeouttheworncarbonbrushes,insertthenew

onesandsecurethebrushholdercaps.

►Fig.27: 1. Brush holder cap

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HS6601 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info