Bedienungsanleitung Makita LS1219L (Seite 27 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691824

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

27 ENGLISH

(a) (b) (c) (d)

1. Inside corner 2. Outside corner

Table (C)

– Molding

position in

the gure

Miter angle Finished

piece

For inside

corner

(a) Right 45° Save the right

side of blade

(b) Left 45° Save the left

side of blade

For outside

corner

side of blade

(d) Right 45° Save the left

side of blade

Cutting aluminum extrusion

►Fig.52: 1. Vise 2. Spacer block 3. Guide fence

4.Aluminumextrusion5. Spacer block

When securing aluminum extrusions, use spacer blocks

orpiecesofscrapasshownintheguretoprevent

deformation of the aluminum. Use a cutting lubricant

when cutting the aluminum extrusion to prevent build-up

of the aluminum material on the blade.

WARNING: Never attempt to cut thick or

round aluminum extrusions. Thick or round alumi-

numextrusionscanbedifculttosecureandthework

may loosen during the cutting operation which may

resultinlossofcontrolandseriouspersonalinjury.

Wood facing

WARNING: Use screws to attach the wood

facing to the guide fence. The screws should be

installed so that the screw heads are below the

surface of the wood facing so that they will not

interfere with the positioning of the material being

cut. Misalignment of the material being cut can case

unexpected movement during the cutting operation

which may result in a loss of control and serious

personalinjury.

CAUTION: Use straight wood of even thick-

ness for the wood facing.

CAUTION: In order to completely cut through

workpieces with a height of 107 mm to 120 mm, a

wood facing should be used on the guide fence.

The wood facing will space the workpiece away from

the fence allowing the blade to complete a deeper

cut.

NOTICE: When the wood facing is attached, do

not turn the turn base with the handle lowered.

The blade and/or the wood facing will be damaged.

Use of wood facing helps to assure splinter-free cuts

inworkpieces.Attachawoodfacingtotheguidefence

using the holes in the guide fence and 6 mm screws.

Seethegureconcerningthedimensionsforasug-

gested wood facing.

►Fig.53: 1. Hole 2. Over 15 mm 3. Over 270 mm

4. 90 mm 5. 145 mm 6. 19 mm 7. 115 -

120 mm

EXAMPLE When cutting workpieces 115 mm and

120 mm high, use a wood facing with the following

thickness.

Miter angle Thickness of wood facing

115 mm 120 mm

0° 20 mm 38 mm

Left and Right 45° 15 mm 25 mm

Left and Right 60° 15 mm 25 mm

Groove cutting

WARNING: Do not attempt to perform this

type of cut by using a wider type blade or dado

blade.Attemptingtomakeagroovecutwithawider

blade or dado blade could lead to unexpected cutting

results and kickback which may result in serious

personalinjury.

WARNING: Be sure to return the stopper arm

to the original position when performing other

than groove cutting.Attemptingtomakecutswith

the stopper arm in the incorrect position could lead to

unexpected cutting results and kickback which may

resultinseriouspersonalinjury.

For a dado type cut, perform as follows:

1. Adjustthelowerlimitpositionofthebladeusing

theadjustingscrewandthestopperarmtolimitthecut-

ting depth of the blade. Refer to "Stopper arm" section

described on previously.

2. Afteradjustingthelowerlimitpositionoftheblade,

cut parallel grooves across the width of the workpiece

using a slide (push) cut.

►Fig.54: 1. Cut grooves with blade

3. Remove the workpiece material between the

grooves with a chisel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1219L Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info