Bedienungsanleitung Makita LS1219L (Seite 25 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691824

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

25 ENGLISH

8. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at the angle shown in the table.

Miter angle Bevel angle

Left and Right 0° - 45° Left and Right 0° - 45°

When performing compound cutting, refer to "Press cut-

ting", "Slide (push) cutting", "Miter cutting" and "Bevel

cut" explanations

Cutting base boards

CAUTION: Make sure to use the horizontal

vise (optional accessory) when cutting the base

board.

CAUTION: When cutting the workpiece of the

thickness 20 mm or thinner, make sure to use a

spacer block to secure the workpiece.

When cutting the base board in 45° miter angle, engage

the stopper lever to prevent the blade case from con-

tacting the base board. This will keep the clearance

between the base board and the blade case when the

carriage is fully pushed forward.

RefertotheSPECIFICATIONSforbaseboardcutting

capacity.

►Fig.46: 1. Stopper lever 2. Spacer block

3. Horizontal vise

Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound

mitersawwiththemoldingslaidatontheturnbase.

There are two common types of crown moldings and

one type of cove moldings; 52/38° wall angle crown

molding, 45° wall angle crown molding and 45° wall

angle cove molding.

►Fig.47: 1. 52/38° type crown molding 2. 45° type

crown molding 3. 45° type cove molding

Therearecrownandcovemoldingjointswhichare

madetot"Inside"90°corners((a)and(b)inthegure)

and"Outside"90°corners((c)and(d)inthegure.)

(a) (b) (c) (d)

1. Inside corner 2. Outside corner

(a)

(b)

(a)

(b)

(a)

(b)

(a)

(b)

(c)

(d)

1. Inside corner 2. Outside corner

Measuring

Measurethewallwidth,andadjustthewidthofthe

workpieceaccordingtoit.Alwaysmakesurethatwidth

of the workpiece's wall contact edge is the same as wall

length.

►Fig.48: 1. Workpiece 2. Wall width 3. Width of the

workpiece 4. Wall contact edge

Alwaysuseseveralpiecesfortestcutstocheckthe

saw angles.

When cutting crown and cove moldings, set the bevel

angleandmiterangleasindicatedinthetable(A)and

position the moldings on the top surface of the saw

base as indicated in the table (B).

In the case of left bevel cut

(a) (b) (c) (d)

1. Inside corner 2. Outside corner

Table (A)

– Molding

position

in the

gure

Bevel angle Miter angle

52/38°

type

45° type 52/38°

type

45° type

For

inside

corner

(a) Left

33.9°

Left 30° Right

31.6°

Right

35.3°

(b) Left

31.6°

Left

35.3°

For

outside

corner

(c)

(d) Right

31.6°

Right

35.3°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1219L Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info