Bedienungsanleitung Makita LS1219L (Seite 24 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691824

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

24 ENGLISH

NOTICE: Before use, be sure to unlock the stop-

per pin and release the handle from the lowered

position.

NOTICE: Do not apply excessive pressure on the

handle when cutting. Too much force may result in

overloadofthemotorand/ordecreasedcuttingef-

ciency. Press down handle with only as much force as

necessaryforsmoothcuttingandwithoutsignicant

decrease in blade speed.

NOTICE: Gently press down the handle to per-

form the cut. If the handle is pressed down with force

or if lateral force is applied, the blade may vibrate and

leave a mark (saw mark) in the workpiece and the

precision of the cut may be impaired.

NOTICE: During a slide cut, gently push the

carriage toward the guide fence without stopping.

If the carriage movement is stopped during the cut, a

mark will be left in the workpiece and the precision of

the cut will be impaired.

Press cutting

WARNING: Always lock the sliding movement

of the carriage when performing a press cutting.

Cutting without lock may cause possible kickback

whichmayresultinseriouspersonalinjury.

Workpieces up to 92 mm high and 183 mm wide can be

cut in the following manner.

►Fig.43: 1. Stopper pin

1. Push the carriage toward the guide fence until it

stops and lock it with the stopper pin.

2. Secure the workpiece with the proper type of vise.

3. Switch on the tool without the blade making any

contact and wait until the blade attains full speed before

lowering.

4. Gently lower the handle to the fully lowered posi-

tion to cut the workpiece.

5. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Slide (push) cutting (cutting wide

workpieces)

WARNING: Whenever performing a slide cut,

rst pull the carriage full towards you and press

the handle all the way down, then push the car-

riage toward the guide fence. Never start the cut

with the carriage not pulled fully toward you. If

you perform the slide cut without the carriage pulled

fully toward you unexpected kickback may occur and

seriouspersonalinjurymayresult.

WARNING: Never attempt to perform a slide

cut by pulling the carriage towards you. Pulling

the carriage towards you while cutting may cause

unexpected kickback resulting in possible serious

personalinjury.

WARNING: Never perform the slide cut with

the handle locked in the lowered position.

►Fig.44: 1. Stopper pin

1. Unlock the stopper pin so that the carriage can

slide freely.

2. Secure the workpiece with the proper type of vise.

3. Pull the carriage toward you fully.

4. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

5. Press the handle down and push the carriage

toward the guide fence and through the workpiece.

6. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Miter cutting

Refertothepreviouslycovered"Adjustingthemiter

angle".

Bevel cut

WARNING: After setting the blade for a bevel

cut, ensure that the carriage and blade will have

free travel throughout the entire range of the

intended cut before operating the tool. Interruption

of the carriage or blade travel during the cutting oper-

ation may result in kickback and serious personal

injury.

WARNING: While making a bevel cut keep

hands out of the path of the blade. The angle of the

blade may confuse the operator as to the actual blade

path while cutting and contact with the blade will

resultinseriouspersonalinjury

WARNING: The blade should not be raised

until it has come to a complete stop. During a

bevel cut the piece cut off may come to rest against

the blade. If the blade is raised while it is rotating the

cut-offpiecemaybeejectedbythebladecausing

the material to fragment which may result in serious

personalinjury.

NOTICE: When pressing down the handle, apply

pressure in parallel with the blade. If a force is

applied perpendicularly to the turn base or if the pres-

sure direction is changed during a cut, the precision

of the cut will be impaired.

►Fig.45

1. Remove the upper fence on the side that you are

going to tilt the carriage.

2. Unlock the stopper pin.

3. Adjustthebevelangleaccordingtotheprocedure

explainedinthe"Adjustingthebevelangle"section.

Then tighten the knob.

4. Secure the workpiece with a vise.

5. Pull the carriage toward you fully.

6. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

7. Gently lower the handle to the fully lowered posi-

tion while applying pressure in parallel with the blade

and push the carriage toward the guide fence to cut

the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1219L Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info