Bedienungsanleitung Makita LS1219L (Seite 22 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691824

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

22 ENGLISH

Removing and installing saw blade

WARNING: Always be sure that the tool is

switched off and unplugged before installing or

removing the blade.Accidentalstartupofthetool

mayresultinseriouspersonalinjury.

WARNING: Use only the Makita wrench pro-

vided to install or remove the blade. Failure to use

thewrenchmayresultinovertighteningorinsufcient

tightening of the hex socket bolt and serious personal

injury.

Alwayslockthecarriagewithraisedpositionwhen

removing and installing the blade. Pull the stopper pin

and rotate it 90° with the carriage raised.

►Fig.29: 1. Unlocked position 2. Locked position

3. Stopper pin

Removing the blade

Loosen the hex bolt holding the center cover using the

hex wrench. Raise the blade guard and center cover.

►Fig.30: 1. Center cover 2. Hex wrench 3. Blade

guard

Press the shaft lock to lock the spindle and use the hex

wrench to loosen the hex socket bolt. Then remove the

hexsocketbolt,outerangeandblade.

►Fig.31: 1. Shaft lock 2. Hex wrench 3. Hex socket

bolt (left-handed) 4. Loosen 5. Tighten

Installing the blade

Mount the blade carefully onto the spindle, making

sure that the direction of the arrow on the surface of the

blade matches the direction of the arrow on the blade

case.

►Fig.32: 1.Arrowonthebladecase2.Arrowonthe

blade

Installtheouterangeandhexsocketbolt.Tightenthe

hex socket bolt counterclockwise using the hex wrench

while pressing the shaft lock.

►Fig.33: 1. Hex socket bolt 2.Outerange3. Saw

blade 4.Innerange5. Spindle 6. Ring

NOTICE:Iftheinnerangeisremoved,besureto

install it on the spindle with its protrusion facing away

fromtheblade.Iftheangeisinstalledincorrectly,the

angewillrubagainstthemachine.

Return the blade guard and center cover to its original

position. Then tighten the hex bolt clockwise to secure

the center cover. Unlock the stopper pin to release

carriage from the raised position. Lower the handle to

make sure that the blade guard moves properly. Make

sure shaft lock has released spindle before making cut.

WARNING: Before mounting the blade onto

the spindle, always be sure that the correct ring

for the blade's arbor hole you intend to use is

installed between the inner and the outer anges.

Use of the incorrect arbor hole ring may result in the

improper mounting of the blade causing blade move-

ment and severe vibration resulting in possible loss

of control during operation and in serious personal

injury.

Connecting a vacuum cleaner

When you wish to perform clean cutting operation, con-

nect a Makita vacuum cleaner to the dust nozzle using

a front cuff 24 (optional accessory).

►Fig.34: 1. Front cuff 24 2. Hose 3. Vacuum cleaner

Dust bag

The use of the dust bag makes cutting operations clean and

dust collection easy. To attach the dust bag, remove the

dust extraction hose on the tool and connect the dust bag.

►Fig.35: 1. Dust extraction hose 2. Dust bag

When the dust bag is about half full, remove the dust

bag from the tool and pull the fastener out. Empty

the dust bag of its contents, tapping it lightly so as to

remove particles adhering to the insides which might

hamper further collection.

►Fig.36: 1. Fastener

Securing workpiece

WARNING: It is extremely important to always

secure the workpiece correctly with the proper

type of vise or crown molding stoppers. Failure to

dosomayresultinseriouspersonalinjuryandcause

damage to the tool and/or the workpiece.

WARNING: After a cutting operation do not

raise the blade until it has come to a complete

stop. The raising of a coasting blade may result in

seriouspersonalinjuryanddamagetotheworkpiece.

WARNING: When cutting a workpiece that

is longer than the support base of the saw, the

material should be supported the entire length

beyond the support base and at the same height

to keep the material level. Proper workpiece support

will help avoid blade pinch and possible kickback

whichmayresultinseriouspersonalinjury.Donot

rely solely on the vertical vise and/or horizontal vise

to secure the workpiece. Thin material tends to sag.

Support workpiece over its entire length to avoid

bladepinchandpossibleKICKBACK.

►Fig.37: 1. Support 2. Turn base

Guide fences

WARNING: Before operating the tool, make

sure that the upper fence is secured rmly.

WARNING: Before bevel-cutting, make sure

that no part of the tool, especially the blade, con-

tacts the upper and lower fences when fully low-

ering and raising the handle in any position and

while moving the carriage through its full range

of travel. If the tool or blade makes contact with

the fence this may result in kickback or unexpected

movementofthematerialandseriouspersonalinjury.

Use upper fences to support the material higher than

the lower fences. Insert the upper fence into the hole on

the lower fence and tighten the clamping screw.

►Fig.38: 1. Upper fence 2. Lower fence 3. Clamping

screw 4.Adjustingscrew

Makita LS1219L Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info