Bedienungsanleitung Makita LS1219L (Seite 21 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691824

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

21 ENGLISH

CAUTION: After changing the bevel angle,

always secure the knob.

Slide lock

To lock the sliding movement of the carriage, push the

carriage toward the guide fence until it stops. Pull the

stopper pin and rotate it 90°.

►Fig.23: 1. Unlocked position 2. Locked position

3. Stopper pin

Switch action

WARNING: Before plugging in the tool,

always check to see that the switch trigger actu-

ates properly and returns to the "OFF" position

when released. Do not pull the switch trigger hard

without pressing in the lock-off button. This can

cause switch breakage. Operating a tool with a

switch that does not actuate properly can lead to loss

ofcontrolandseriouspersonalinjury.

WARNING: NEVER use tool without a fully

operative switch trigger.Anytoolwithaninoper-

ativeswitchisHIGHLYDANGEROUSandmustbe

repaired before further usage or serious personal

injurymayoccur.

WARNING: NEVER defeat the lock-off button

by taping down or some other means.Aswitchwith

a negated lock-off button may result in unintentional

operationandseriouspersonalinjury.

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press-

ing the lock-off button.Aswitchinneedofrepair

may result in unintentional operation and serious

personalinjury.ReturntooltoaMakitaservicecenter

for proper repairs BEFORE further usage.

►Fig.24: 1. Switch trigger 2. Lock-off button 3. Hole

for padlock

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

Aholeisprovidedintheswitchtriggerforinsertionofa

padlock to lock the tool off.

WARNING: Do not use a lock with a shank

or cable any smaller than 6.35 mm in diameter.A

smaller shank or cable may not properly lock the tool

in the off position and unintentional operation may

occurresultinginseriouspersonalinjury.

Electronic function

Constant speed control

The tool is provided with an electronic speed control

which helps maintain a constant blade rotation speed

evenunderload.Aconstantbladerotationspeedwill

result in a very smooth cut.

Soft start feature

This function allows the smooth start-up of the tool by

limiting the start-up torque.

Laser beam action

For model LS1219L only

CAUTION: Never look into the laser beam.

Directlaserbeammayinjureyoureyes.

To turn on the laser beam, press the upper position (I)

of the switch. To turn off the laser beam, press the lower

position (0) of the switch.

►Fig.25: 1. Switch for laser

Laser line can be shifted to either the left or right side of

thesawbladebyturningtheadjustingscrewasfollows.

►Fig.26: 1.Adjustingscrew

1. Loosentheadjustingscrewbyturningit

counterclockwise.

2. Withtheadjustingscrewloosened,slidethe

adjustingscrewtotherightorleftasfarasitgoes.

3. Tightentheadjustingscrewrmlyattheposition

where it stops sliding.

NOTE:Laserlineisfactoryadjustedsothatitisposi-

tioned within 1 mm from the side surface of the blade

(cutting position).

NOTE: When laser line appears dim and hard to see

because of direct sunlight, relocate the work area to a

place where there is less direct sunlight.

Aligning the laser line

Alignthecuttinglineonyourworkpiecewiththelaser

line.

►Fig.27

A)Whenyouwanttoobtainthecorrectsizeontheleft

side of workpiece, shift the laser line to the left of the

blade.

B) When you want to obtain the correct size on the right

side of workpiece, shift the laser line to the right of the

blade.

NOTE: Use wood facing against the guide fence

when aligning the cutting line with the laser line at the

side of guide fence in compound cutting (bevel angle

45° and miter angle right 45°).

ASSEMBLY

WARNING: Always be sure that the tool is

switched off and unplugged before working on

the tool. Failure to switch off and unplug the tool may

resultinseriouspersonalinjury.

Hex wrench storage

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

►Fig.28: 1. Hex wrench

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1219L Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info