Bedienungsanleitung Marantz Model 1060 (Seite 5 von 13) (Englisch)

571043

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

PREPARATIONFORUSE

Rear panel Signal Connection

All signal connections to the Model 1060 should be

made with shielded audio cables. Figure 2 shows

the location of the input and output jacks on the

rear panel. These are for "permanent" connections.

Use of the front panel controls and jacks will be

discussed later. A letter "L" corresponds to the left

audio channel; a letter "R" to right audio channel.

To avoid confusion, it is suggested that you

connect one cable at a time between the Model

1060 and the other components of your system.

This way, mixing up the channels or mixing up

signal sourcesand destinations will be avoided.

The SPEAKER SYSTEM (MAIN, REMOTE) jacks

on the left side of the rear panel will accomodate

two loudspeaker systems; each speaker having a

rated impedance between 4 and 16 ohms. When

using only one pair of speakers, connect them to

the terminals marked MAIN. The terminals marked

REMOTE are used for connection a second pair of

speakers in a location remote to the Model 1060.

Use care when connecting the Model 1060 to a

loudspeaker which contains a built-in power

supply-such as an electrostatic loudspeaker. The

"common" speaker-connection terminal of these

devices may be capacitively coupled through the

power supply. Ensure that the (-) terminals of the

model 1060 are connected to the "common"

SYSTEM 1 REPEAT WIRI NG

AS FOR SYSTEM 1

COM.

RIGHT

LEFT

Figure1. LoudspeakerSystem Connections

terminals of the loudspeaker system as shown in

Figure 1. Ordinary #18 gaugetwo-conductor lamp

cord may be used for distances of up to 30 feet

between amplifier and loudspeakers. For longer

distances, use#16 gaugewire or heavier, depending

on length.

In connecting two loudspeakers for stereo opera-

tion, it is important to insure correct relative

phasing (polarity). This is best acheived, when

using identical loudspeakers, by simply coding each

wire for identification, one wire in each pair

should be coded at both ends with a knot, tape,

etc. The coded wires can then be used for identical

connections in each channel. For example, the

coded wire in each pair can be connected to the

"common" terminal of each loudspeaker and the

(-) terminal of each amplifier channel. The un-

coded wire of each pair is then connected to the

remaining loudspeaker terminal and the remaining

terminal on each amplifier channel (R and L). This

procedure insures correct polarity or phasing of

identical loudspeakers.

Note: Close inspection of standard zipcord will

reveal some form of coding on the insulation (ridge

or groove on one edge); or one of the wires may be

tinned and the other wire not tinned.

CAUTION: Never directly connect the loudspeaker

terminals of one channel in parallel with those of

any other. Any resulting damage is not covered

under warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz Model 1060 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info