Bedienungsanleitung Marantz Model 1060 (Seite 6 von 13) (Englisch)

571043

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

01N Tape recorder jack (REC/PLAY)- The 5-pin

DIN tape recorder jack on the rear panel permits

use of European-type 5-wire tape recorder cables

with similarly equipped tape recorde"rs. This jack is

connected in parallel with the TAPE IN and TAPE

OUT jacks, but the polarizing pin in the plug

assures proper phasing at all" times.

TAPE OUT jacks-The signals available at this pair

of jacks may be routed to your tape recorder and

are affected only by the selector switch on th~

front panel.

TAPE IN jacks-With tape recorder pre-amplifier

outputs connected to these jacks, signals from a

tape recorder can be played through your system

when the recorder is set for playback mode of

operation and the TAP E MaN switch is in the IN

position.

AUX 1 jacks-These high level jacks provide for

connecting miscellaneous sources such as tape i

players with self-contained playback preamplifiers, I

phono cartridges that provided RIAA equal ized

high-level output, or additional tuners or receivers,

etc.

TUNER jacks-These high level jacks can be used

for connecting a stereo or mono tuner to the

Model 1060.

For stereo (multiplex) FM tuner reception, pro-

ceed asfollows:

Connect a pair of audio cables between the

tuner's right and left output jacks and the

Model 1060's right and left jacks. Set the

front panel selector switch to TUNER.

1:.-f1iJJ{V{)

CW vJ 1~€:

Figure 2. Rear Panel Connection Facilities

For monophonic FM or AM tuners, proceed as

follows:

Connect one cable to either left or right

TUN ER jack. Set the front panel selector

switch to TUNER and depress both MONO

, IN (L,R) pushswitches.

;I~HONO jacks-These jacks are for use with stand-

ard phono cartridges requiring a 47,000 ohm

resistive load.

If hum is heard when playing records, it is evidence

of inadequate grounding or shielding of your

record player or connections. Connect a separate

ground wire from the turntable or record changer

frame to the CHASSIS GROUND binding post on

the Model 1060. If the tone arm is mounted on a

wood panel or is otherwise insulated from the

frame, connect the arm's mounting base to the

I grounding wire with a short jumper. If the two

pairs of signal wires in the arm have a single overall

shield, connect the shield to the grounding wire,

keep the two phono connecting cables and ground-

ing wire closely together. In three-wire (common

ground) systems, this will minimize "ground

loops".

If excessive phono hum persists, your

I phono cartridge may have a clip connecting the

I two "common" wires together, remove it.

TAPE jacks-tOo not confuse the TAPE jacks with

the TAPE INor TAPE OUT jacks.) An extra tape

recorder can be connected to the TAPE jacks.

! When playing back with the tape recorder con-

nected to the TAPE jacks, place the selector switch

on the front panel in the TAPE position. The

I TAPE jacks are not affected by the TAPE MaN

pushswitch

on the front panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz Model 1060 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info