Bedienungsanleitung Marantz Model 1060 (Seite 7 von 13) (Englisch)

571043

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

PRE OUT jacks-These jacks deliver the output of

the Model 1060 preamplifier circuits to the rear

panel.

MAIN IN jacks-These are the input terminals of

the power amplifier section of the Model 1060.

Note: The PRE OUT and MAIN IN jacks are

normally bridged by two molded

RCA type pin

plug assemblies which are provided with each

Model 1060. These assemblies must remain intact

for normal operation of the unit. However, should

you intend to use such equipment as a graphic

equalizer, compressor/limiter, or expander, you I

may connect these instruments to your Model:

1060 by removing the bridging connections from

the rear panel PRE OUT and MAIN IN jacks and

connecting appropriate length shielded audio Ii

cables from your Model 1060 to your processing

equipment.

CHASSIS GROUND-This binding post provides a I

convenient "earth" ground point to eliminate

possible ground loops between the Model 1060 and

program sources.

Convenience Outlets -Two AC outlets

on the rear

panel are provided for powering associated com- ~

ponents of your system, such as power amplifiers,

tuners, tape recorders, record players, etc. The

right one is controlled by the front panel POWER,

switch. The UNSWITCHED outlet is not controlled

by the POWER switch. This outlet is for powering

a turntable or record changer that has its own

on-off switch.

OPERATION

Simplified Operating Procedures-When operating

the Model 1060 Stereo Consolefor the first time,

follow these simple directions, using Figure 3.

Later 0 n, you can take fu II advantage of the

instrument's versatility by learning to use the

remaining controls and adjustments.

I Step 1. Turn the volume control all the way to the

left (fully counter-clockwise), and set the balance

control to mid-position.

Step 2. Set MONO IN (L,R) pushswitch to the

OUT position.

Step 3. Set TAPE NON pushswitch

to the OUT

position.

Step 4. Set all treble, mid and bass controls to the

center position.

I' Step 5. Depressthe POWER $witch. The pilot light

at the right center of the panel will glow.

Step 6. Select the desired program source by

turning the selector switch to the appropriate

position-unless the desired program source is a

recorded tape to be played by the taperecorder

which is connected to the DIN type recorder jack

or TAPE INjacks. MIC,PHONO,TAPE,AUX 10r

AUX 2 may be sele~ted, by the selector switch.

The TAPE, TUNER or AUX 1 positions select the

program sources connected to the corresponding

input jacks on the rear panel.

I mic/aux 2 jacks-These jacks accept the standard

2-conductor phone

plug.

1. When one low level microphone (less than

100mV, such as a dynamic type) is connected

to the "L" jack of the mic/aux 2 jacks, place

the selector switch in the MIC position. The

sound can be heard through the left channel

loudspeaker. In this case depress the MONO IN

(L) pushswitch to listen the sound from both

channel loudspeakers. If the microphone is

connected to the IIR" jack, depress the MONO

IN (R) pushswitch to hear the sound through

both channel speakers and release the (R) push-

switch to listen the sound through R channel

speaker only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz Model 1060 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info