Bedienungsanleitung Marantz SR-7200 (Seite 19 von 39) (Englisch)

6590

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

ENGLISH

BASIC OPERATION

LISTENING TO THE TUNER

MANUAL TUNING

1. To select the tuner as the source, press the TUNER button t on

the front panel or press the TUNER button , on the remote

control unit.

2. Press the TUNER button t on the front panel or press the

TUNER button , on the remote control unit to select the desired

frequency band if required.

3. Press the F/P button !6 on the front panel to display the frequency.

4. Press the TUNING/PRESET or button !5 on the front panel or

press the ^, v button ⁄0 on the remote control unit.

5. If FM is selected, press the MODE button !7 on the front panel or

select T-MOD by the Jog Dial n and press the ENT button m in

the TUNER mode on the remote controller.

(FM) MODE BUTTON OPERATION

When “AUTO” indicator is on in the display, FM stations that broadcast

in stereo will be received in stereo and the “STEREO” indicator lights.

When “AUTO” indicator is off, all the FM stations will be received in

mono regardless of whether or not they are broadcasting in stereo.

AUTO TUNING

1. Press the F/P button !6 on the front panel to display the frequency.

2. Press the TUNING/PRESET or button !5 on the front panel

for more than 1 second to start the Auto tuning function.

AUTO TUNING (USING THE REMOTE CONTROL UNIT)

Press ^, v button ⁄0 for more than 1 second to start the Auto tuning

function.

PRESET TUNING

With this unit you can preset up to 30 FM/AM stations in any order. For

each station, you can memorize the frequency and reception mode if

desired.

1-a. Manual Presetting

1. Refer to the “MANUAL TUNING” or “AUTO TUNING” section

above to tune in a desired station.

2. Press the MEMORY button !4. “MEMORY” indicator starts blinking

on the display.

While “MEMORY” is still blinking (approx. 5 seconds), select the

preset number by pressing the TUNING/PRESET or button !5

then press the MEMORY button !4 again.

3. When a number has been properly input, “MEMORY” indicator

stops blinking and goes out.

The station is now stored in the specified preset memory location.

1-b. Manual Presetting (Using the remote unit)

1. Tune in a desired station.

2. Press the MEMO button ⁄6.

3. Enter the desired preset number with ten keypad ⁄7.

4. Then, press MEMO button ⁄6 again to store.

2. Auto Presetting

This function automatically scans the FM and AM band and enters all

stations with sufficient signal strength into the memory.

1. Press and hold down the MEMORY button !4 and TUNER button

t simultaneously for 3 seconds or more.

2. “MEMORY“ will blink on the display.

3. Each time the tuner finds a station, the scanning will pause and

memory. Auto presetting will starts.

4. Operation stops automatically when all 30 preset memory

positions are filled or when auto scanning attains the highest end

of all bands.

To stop the auto preset function at anytime, press the CLEAR

button !3.

3. Recalling a Preset Station

1. Press the F/P button !6 to change the display to preset.

2. Select the desired preset station by pressing TUNING/PRESET

or button !5 on the front panel or press CH or CH button ⁄2

on the remote.

Note:

To directly access the preset stations using the numeric keypad,

select the desired preset station by entering one or two digits using

the numeric keypad ⁄7.

To return to the Manual Tuning mode, press the F/P button !6.

4. Preset Scan Tuning (Using the remote control unit)

1. Select the SCAN by the Jog Dial n and press the ENT button m

in the TUNER mode on the remote controller. (The preset station

with the smallest preset number is recalled first. If no stations have

been preset, “NO PRESET” shows in the display and the unit

returns to the previous mode.)

2. Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5

seconds each. Preset numbers that do not contain stations are

skipped.

3. You can fast forward the preset stations by pressing the CH

button continuously.

When the desired preset station is received, cancel the preset scan

operation by pressing the CH button or the CLEAR button ⁄5.

5. Clearing Preset Stations

You can remove preset stations from memory using the following

procedure.

1. Recall the preset number to be cleared with the method described

in “Recalling” a preset station.

2. Press the CLEAR button !3 on the front panel or CLEAR button

⁄5 on the remote control unit for 3 seconds or more.

“CLEAR” appears on the display to indicate that the specified

preset number has been cleared.

6. Frequency Direct Call

1. Select F-DIR by the Jog Dial n and press the ENT button m in

the TUNER mode on the remote controller.

2. Display shows “FM– – –.––MHz” (at FM mode).

3. Input your desired frequency with tenkeypad buttons on the

remote controller.

Eg) 98.1 MHz

Press 9, 8, 1 and 0

4. Press the ENT button m again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-7200 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR-7200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info