Bedienungsanleitung Marantz SR5004 (Seite 44 von 96) (Englisch)

522801

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

NAMES AND

FUNCTIONS

BASIC

CONNECTIONS

BASIC

OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

ADVANCED

OPERATION

ENGLISH

ADVANCED OPERATION

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT

If you have already assigned the digital inputs, you

can temporarily select the audio input mode for

each input source as following procedures.

Press the AMP button and press the A/D button.

When this button is pressed, the input mode is

switched in the following sequence.

Auto → HDMI → Digital → Analog → Auto

Auto mode:

The types of signals being input to the digital and

analog input jacks for the selected input source are

detected automatically.

If no digital signal is being input, the analog input

jacks are selected automatically.

HDMI mode:

HDMI mode can be selected only when an HDMI

input has been assigned as an input source.

When “HDMI Audio” under Preference of the

Setup Menu is set to “Through”, the HDMI mode

cannot be selected.

Digital mode:

The input signal is ﬁ xed to an assigned digital input

terminal.

Analog mode:

The analog input jacks are selected.

This selection is temporary and will not be stored

in memory.

To store changes to the input mode, select “Input

Setup” from the Main Menu. (See page 25)

Note

• This function cannot be used when performing

USB, M-XPort or Tuner operations.

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source

selected for listening through this unit is sent to the

record outputs.

This means that any program you are watching

or listening to may be recorded simply by placing

machines connected to the outputs for CD/CDR

OUT and VCR OUT in the record mode.

To record the input source signal you are

currently watching or listening to

1. Select the input source to record by turning

the INPUT SELECTOR knob on the front

panel or simply press the input selector

buttons on the remote controller.

The input source is now selected and you

may watch or listen to it as desired.

2. The currently selected input source signal

is output to the CD/CDR OUT and VCR OUT

outputs for recording.

3. Start recording to the recording component

as desired.

Notes

• When connecting only digital signal input, output

cannot be made to the CD/CDR OUT or VCR

OUT terminals. When using recording functions,

be sure to also make connections for analog

signal input.

• Video or audio signals input to HDMI input

terminals cannot be recorded.

• The S-Video or video signals input from the AUX

INPUT terminal are output to the VIDEO OUT

(VCR) terminal.

However, video recording is not possible when

copy control signals are contained in the video

signals.

7.1 CH INPUT

This unit is equipped for future expansion through the

use of Multi channel Super Audio CD multichannel

player or DVD-Audio player.

When this is selected, the input signals connected to

the L(front left), R (front right), CENTER, SL (surround

left), SR (surround right) and SBL (surround back left)

and SBR (surround back right) channels of the 7.1

CH. In jacks are output directly to the front (left and

right), center, surround (left and right) and surround

back speaker systems as well as the pre-out jacks

without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer)

jack is output to the PRE OUT SW (subwoofer) jack.

When 7.1 CH. INPUT is selected, the last video input

used remains routed to the Monitor Outputs.

This permits simultaneous viewing with video

sources

Select a desired Video source to decide the

routed video signal to the Monitor Outputs.

2. Press the 7.1 button on the remote controller

to switch the 7.1 channel input.

3. If it is necessary to adjust the output level of

each channel, press the CH.SEL button on

the remote controller.

Adjust the speaker output levels so that

you can hear the same sound level from

each speaker at the listening position. For

the front left, front right, center, surround

left, surround right and surround back

speakers, the output levels can be adjusted

between –12 to +12 dB.

The subwoofer can be adjusted between

–18 and +12 dB.

These adjustments result will be stored to

7.1 CH. INPUT memory.

4. Adjust the main volume with the MAIN

VOLUME knob or the VOL buttons on the

remote controller.

7.1CH LEVEL ADJUST

FRONT.L LEVEL: 0.0 dB

CENTER LEVEL: 0.0 dB

FRONT.R LEVEL: 0.0 dB

SURR.R LEVEL: 0.0 dB

S.B R LEVEL: 0.0 dB

S.B L LEVEL: 0.0 dB

SURR.L LEVEL: 0.0 dB

SUB W LEVEL: 0.0 dB

To cancel the 7.1 CH. INPUT setting, press the 7.1

button on the remote controller.

Notes

• When the 7.1 CH. Input is in use, you may not

select a surround mode, as the external decoder

determines processing.

• In addition, there is no signal at the record

outputs when the 7.1 CH. Input is in use.

• Furthermore, the following functions are not

available during 7.1 CH Input use.

Test Tone, NIGHT MODE, Source Direct, Pure

Direct, HT-EQ, Tone Control, Acoustic EQ.

ATTENUATION TO ANALOG INPUT

SIGNAL

If the selected analog audio input signal is greater

than the capable level of internal processing, the

“PEAK” indicator will light up on the front display.

If this happens, you should press the ATT button on

the remote controller.

“ATT” indicator will be illuminated when this function

is activated. The signal-input level is reduced by

about half. Attenuation will not work with the output

signal of CD/CDR and VCR-OUT.

This function is memorized for each individual input

source.

Marantz SR5004 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info