Bedienungsanleitung Marmitek RFIX35 (Seite 11 von 11) (Englisch, Holländisch)

494328

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Problem: In the programming mode, the RFIX35 does not accept any

commands.

Cause: No commands are received.

Solution:

Do not send the set-up commands for programming the RFIX35

through the remote control. Use a different Marmitek X-10

component (Home Control Box, PRU256 or Interface module) to send

the set-up commands to the RFIX35 through the lighting circuit.

Electrical equipment and systems can be sensitive to signals from

other equipment, which causes electro magnetic disturbance. In

the European Union, countries agreed upon laws for the immunity

(sensitivity) of signals of other equipment as well as equipment

emission (disturbance). When equipment or applications in a certain

surrounding comply with the valid standards, they will not disturb

each other's operations (they are called "Electro Magnetic

Compatible").

For residential surroundings, where the home automation system

Marmitek X-10 is being applied, the European standard for

immunity is standardised in EN 61000-6-1. Equipment that complies

with this standard is resistant to electro magnetic emission of other

equip ment, which complies with the European standard EN 61000-

6-3 for residential surroundings. Experience has shown that in

domestic surroundings, equipment is being used which has an

EMC-emission level that is above the levels stated in EN 61000-6-3.

This equip ment can disturb the correct functioning of the Marmitek

X-10 modules. The immunity of the Marmitek X-10 built-in modules

is therefore revaluated and equivalent to EN 61000-6-2 (the more

severe European standard for immunity in industrial surroundings).

Nevertheless, the application area for Marmitek X-10 will

remain restricted to residential areas.

Undisturbed functioning of Marmitek X-10 automation

Marmitek is therefore not responsible for the disfunctioning of

the Marmitek X-10 system as a consequence of equipment in the

building with emission levels that exceed the maximum allowed

levels set as standard for residential, commercial and semi-

industrial surroundings stated in EN 61000-6-3.

Application area Valid European Standard Marmitek X-10

home automation*

Immunity of Emission of Immunity and

equipment equipment

emission standards

Residential 61000-6-1 61000-6-3 Compatible/

Commercial meets the

Semi-industrial requirements

* Condition is that the total Marmitek X-10 system is installed in accordance

with valid instructions supplied by a certified and trained Marmitek X-10

dealer.

Copyrights

Marmitek is a trademark of Pattitude B.V., RFIX35™ is a trademark of Marmitek

(including but not limited to model numbers, software, audio, video, text and

photographs) rests with Marmitek B.V. Any use of the Content, but without limi-

tation, distribution, reproduction, modification, display or transmission without

the prior written consent of Marmitek is strictly prohibited. All copyright and

other proprietary notices shall be retained on all reproductions.

20325 - 20100928

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek RFIX35 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info