Bedienungsanleitung Marmitek RFIX35 (Seite 9 von 11) (Englisch, Holländisch)

494328

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

The RFIX35 is now in the

RF-secured receiving mode. To link

a remote control please send an

address and a command with the

remote control in the RF-secured

mode (see page 51 and 52) that you

want to link to the RFIX35.

When the RFIX35 accepts the

remote control the RFIX35 will

return to the operation mode (LED OFF).

If you want to link more remote controls please repeat this

procedure for all other remote controls you want to link up to a

maximum of 8. When the memory of the RFIX35 is full it will not

Programming the RFIX35 (cont'd.)

accept any remote control. The LED of the RFIX35 will be lit for

2 sec. and will return to the normal operation mode without

storing the remote control. If you accidentally link a remote

control that was already linked it will be accepted without

"claiming" any extra memory space.

Note: If the same remote control is linked with a

new random generated security code, extra memory

space will be claimed.

The RFIX35 will automatically return to the operation mode when

it does not receive any commands within 60 seconds.

Delete all linked remote controls from memory

If you have already linked 8 remote controls and want to link a new

remote control to the RFIX35, you will first have to clear the

memory of the RFIX35. This is possible by first setting the RFIX35

in the RF-secured programming mode (keep programming switch

pressed and release the switch after 6 seconds. The LED will give

quick short blinks). In the RF-secured mode press the programming

switch and keep it pressed. Release the programming switch after

9 seconds. All previously linked remote controls are now deleted,

the memory is cleared. You can now start the procedure as

previously described to link up to 8 remote controls again.

Programming of the remote control

Programming the RF-secured mode in the remote control

To be able to use the RF-secured mode you first have to

program the remote control to the RF-secured mode.

To program the RF-secured mode in the ABX1 or ABX3 please

follow the steps below.

Setting ABX1 to RF-secured mode

Program in the code 822 via the Marmitek X-10 key

➔ Press SETUP until the LED stays lit

➔ Press the Marmitek X-10 key

➔ Enter 8-2-2, the LED goes out after the last 2

2. Press the Marmitek X-10 key

3. Press SETUP until the LED stays lit

4. Release the SETUP key.

5. Press the A.B. key to generate a random

security code

6. Press the ENT (Enter) key

Return to the standard mode (= non-RF-secured mode)

To return the ABX1 to the standard mode, program in the code

820 via the Marmitek X-10 key.

➔

Press SETUP until the LED stays lit

➔

Press the Marmitek X-10 key

➔

Enter 8-2-0, the LED goes out after the 0

Programming the remote control (cont'd.)

Setting ABX3 to RF-secured mode

1. Remove the batteries.

2. Press the keys to release the last bit of energy

from the remote control.

3. Set the switch to position 2.

4. Now place the batteries in the remote control.

Return to the standard mode (= non-RF-secured mode)

To return the ABX3 to the normal mode, follow the

instructions below:

1. Remove the batteries.

2. Press the keys to release the last bit of energy from the

remote control.

3. Set the switch to position 1.

4. Now place the batteries in the remote control.

• The RFIX35 is designed to be:

- installed on a standard 50 mm junction box or

- installed below a (ceiling) distribution box, or

- mounted on a wall (using supplied power cable).

• When installing in a meter box, you must ensure that the plug

of the RFIX35 is inserted in a socket that is electrically "after"

the filter.

Note: Automatic switching does not just increase

the level of comfort, a number of hazards are also

involved. People may be surprised, or clothing pla-

ced over an electrical heat source may ignite.

Always be aware of these hazards and take the

necessary precautions.

• The product must only be opened for installation purposes.

We advise you to have the product installed by a trained and

certified Marmitek X-10 dealer.

Installation methods

Installation methods (cont'd.)

• If the mains lead supplied is used, the wire ends must be

installed up to the insulation in the connector. There must not

be any bare copper visible.

• Ensure that the built-in antenna is at a sufficient distance from

metal parts and cabling.

• Never install the RFIX35 against a metal rear wall.

• Install the RFIX35 at a sufficient distance from other

RF transmitters, such as WIFI routers and DECT telephones

etc. This equipment can interfere with the reception of the

RFIX35. Install the RFIX35 at least 1.5 metres from such

equipment, as centrally as possible in the home (in electrical

terms).

• To prevent short circuits, this product should only be used

inside and only in dry spaces. Do not expose the components

to rain or moisture. Do not use the product close to a bath,

swimming pool etc.

• Do not expose the components of your systems to extremely

high temperatures or bright light sources.

• Only connect the product to the mains after checking

whether the mains voltage is the same as the values on the

identification tags. Never connect a power cord when it is

damaged. In that case, please contact your supplier.

Marmitek RFIX35 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info