494328
7
Zoom out
Zoom in
Vorherige Seite
1/11
Nächste Seite
37
A
Fitting to a distribution box.
38
Connecting the power cord for use in a wall socket
If you wish to connect the RFIX35 to a wall socket, you must
connect the power cord provided.
To connect the power cord to the RFIX35, follow the steps
below.
Remove the cover of the RFIX35 by loosening the screw
at the top.
Use a Stanley knife to carefully cut open the recess on the
narrow side of the mounting plate so that the power cord
can be fed through.
Fit live and neutral to the connector and feed the cable
through the cable channel in the mounting plate.
Firmly tighten the cover of the RFIX35 to the mounting
plate again.
Assembly
(cont'd.)
39
Connecting of the power cord.
40
Standard or RF-secured mode
The RFIX35 can operate in
RF-secured mode
or standard mode (default).
Remote control RFIX35
Standard mode
RF-secured mode
Standard mode
RF-secured mode
41
Standard mode
In the standard mode the RFIX35 is compatible with existing
remote controls. In this mode the user must press separately
the address number and the command on the remote control.
The RFIX35 will receive the RF signals from the remote control
(an address with a command) and transmit it over the power
line to activate actuators or start macros.
RF-secured mode
In the RF-secured mode only commands from linked remote
controls will be accepted. Commands from other remote
controls within the receiving reach of the RFIX35 will be
ignored. To be able to use the RF-secured mode you will need
a remote control containing RF-security code. Up to 8 different
remote controls can be linked. Remote controls that are suitable
for RF-secured are the Marmitek X-10 ABX1 and the ABX3.
42
Receiving modes
Note: The default setting of the RFIX35 is letter
code "A" in the standard mode. In this mode, the
RFIX35 will accept commands on the same letter
code from other remote controls that are within
the range of the RFIX35. If you select letter code
"P" in the standard mode, the RFIX35 will also
accept commands from the other letter codes
within the range. As a result, third parties can
operate your lighting and equipment connected to
Marmitek X-10 Home. If you want to avoid this,
you must program the remote controls to the RF-
secured mode.
!
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marmitek RFIX35 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info