Bedienungsanleitung Marmitek RFIX35 (Seite 10 von 11) (Englisch, Holländisch)

494328

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

• Do not open the product: the device contains live parts. The

product should only be repaired or serviced by a qualified

repairman.

• In case of improper usage or if you have opened, altered and

repaired the product yourself, all guarantees expire. Marmitek

does not accept responsibility in the case of improper usage

of the product or when the product is used for purposes other

than specified. Marmitek does not accept responsibility for

additional damage other than covered by the legal product

responsibility.

The RF communication uses the 433.92 MHz

communication band. This band is a non-exclusively

available communication band. Therefore, interference

and limitations in range cannot be completely eliminated.

The range of the RF signals depends on a number of (external)

factors. Some of these factors are: transmitter power,

installation method and site, air humidity and construction of the

home. The materials used in homes hinder the transmission of

RF signals to some extent. Consequently, the maximum

communication distance in homes is less than the distance that

can be achieved in the open. The following list gives the

damping effect of several materials.

Absorption of RF signals

Wood, plaster, plasterboard approx. 10 %

Brick and stone, chipboard approx. 30 %

Reinforced concrete approx. 70 %

Metal (gauze), aluminium (foil) approx. 90 %

RF-signals

Technical data

Product characteristics

Mains voltage 230 Vac, 50 Hz

Max. power consumption < 2 W

Ambient temperature 0 to 40 °C

Frequency 433,92 MHz; X-10 RF (NEC)

compatible protocol

Max communication distance 100 m (open field)

Protection class Class II, Double insulated

Type of protection

IP 40 with wall or ceiling installation

IP 20 with installation on the wall

Standards IEC 60950

Housing

Dimension (H x W x D) 120 x 80 x 30 mm

Color RAL9001

Power cable

Dimension Length 1.5 m

Color White

Troubleshooting

Problem: The LED on the RFIX35 does not flash when I press the

remote control.

Cause: The remote control batteries are (almost) flat.

Solution: Replace the batteries.

Cause: The remote control (ABX1) is in the IR mode and not in the

RF mode.

Solution: Set the remote control to a RF transmitter.

Cause: The RFIX35 is not set to the same letter code as the remote

control.

Solution: Program in the same letter code on the remote control and the

RFIX35 or program the RFIX to letter code P.

Cause: The remote control is not programmed to the RF-secured mode

but the RFIX35 is.

Solution: Set the remote control to the RF-secured mode.

Cause: The remote control is programmed to the RF-secured mode but

the RFIX35 is not.

Solution: Set the remote control to the standard receive mode.

Cause: The RFIX35 is in the RF-secured mode and the remote control is

not linked.

Solution: Link the remote control in the RF-secured mode.

Cause: RF signals are not received.

Solution: Reduce the distance between the remote control and the RFIX35.

Problem: The transmission range is insufficient.

Cause: The receiver is too close to metal parts.

Solution: Ensure that the RFIX35 is placed away of metal parts. Do not

place on a metal plate.

Cause: Radio frequency signal interferes with the receiver.

Solution: Place the RFIX35 out of range of other electronic equipment.

Cause: The batteries are almost flat.

Solution: Replace the batteries.

Problem: There are spontaneously switching modules.

Cause: Commands from neighbours are received by the RFIX35.

Solution: Do not set the receiver to the same letter code as the neighbours.

Do not set the RFIX35 to letter code P but to a single letter code.

Set the RFIX35 to the RF-secured mode.

Cause: The RFIX35 is set to letter code P and is not programmed to the

RF-secured mode.

Solution: Set the RFIX35 to the RF-secured mode.

Troubleshooting (cont'd.)

Problem: After the remote control batteries are replaced, I cannot

operate anything.

Cause: The remote control batteries are incorrectly positioned or make

insufficient contact.

Solution: Check if the batteries are correctly positioned.

Cause: The letter code of the remote control has been reset to

letter code A.

Solution: Program the correct letter code into the remote control.

Cause: The remote control generates a new RF-security code that is not

recognised.

Solution: Delete all security codes in the RFIX35 and link the remote control

again.

Problem: When programming in the security code, the LED lights up

for 2 seconds.

The RFIX35 does not accept any more security codes.

Cause: The RFIX35 memory is full. All 8 remote controls are linked in the

RF-security mode.

Solution: Clear the RFIX35 memory and link the remote control(s) again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek RFIX35 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info