Bedienungsanleitung Marquant mcr-1290 (Seite 11 von 34) (Holländisch, Französisch)

163890

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

1717

1010

3. Radio Operation

1. BAND BUTTON

In RADIO mode, press the BAND button on the remote controller or on the front panel to

select your desired radio band of FM1, FM2, FM3, MW1 and MW2, and the word means which

band is selected will be displayed on the small monitor of the front panel.

2. TUNE/SEEK UP/DOWN BUTTONS

In RADIO mode:

1) Long press the UP/DN button on the front panel or the >>|/ |<< button on the remote controller

to automatically search up/down for a available station from the current frequency.

2) Briefly press the UP/DN button on the front panel or the >>| / |<< button on the remote controller

to manually search up or down with step by step for your desired station from the current

frequency.

3. APS BUTTON

In RADIO mode:

1) When long pressing the APS button, the radio searches from the lowest frequency and checks

the signal strength level until 1 cycle search is finished. And then the 6 strongest stations are

preset to the corresponding preset number memory bank. The AS operation is implemented in

the each bank of the selected band. When the AS operation is finished, it will resume broad-

casting on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)

2) When briefly pressing the APS button on the front panel or the remote controller, the radio

searches for each preset station from the M1. When the field strength level is more than the

threshold level of the stop level, the radio is holding at that preset number for few seconds with

releasing mute, and then searches again. After finishing a circle of searching, it will stop

searching on the M1.

NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.

4. PRESET STATION [ 1-6 ] BUTTONS

In RADIO mode:

1) To memorize the current frequency on the current band, long press any one of the six preset

buttons (1-6) , or press the ^/v button to select a memory bank and then long press the OK button.

2) To recall the preset memory on the current band, press one of the preset buttons [1-6] or press

the ^ / v button and then press the OK button to confirm.

5. STEREO/MONO BUTTON

Press the ST button on the remote controller to select the STEREO or MONO sound mode for

FM band.

6. LOC BUTTON

1) In FM mode, when the signal of the distance radio station are very weak and the receiving

effect is bad during tuning, check whether there is the word LOC on LCD. If there is the word

LOC on LCD, press this button to turn off the LOC function, then tune again for the distance

radio station;

2) In FM mode, when the signal of the local radio station are too strong to lead that the interference

to the receiving effect during tuning, press this button to turn on the LOC function to display the

word LOC on LCD, then tune again for the local radio station.

ZOOM 2,ZOOM 3,ZOOM 4,ZOOM 1/2,ZOOM 1/3,ZOOM 1/4,ZOOM OFF.

Press one of the ^/v/>/< buttons to select the area you want to enlarge.

5.10 Change the Caption Language

In the state of DVD disc playing, press the SUBTITLE button repeatedly to

select the language of the caption or turn off the caption.(depend on the

disc used.)

In the state of VCD/MP3/WMA/CD disc playing, the button is not available.

5.11 Change the Audio Language

1. In the state of DVD disc playing, press the AUDIO button repeatedly

on the IR remote controller to select the desired language type.

(depend on the disc used)

2. In the state of VCD/MP3/WMA/CD disc playing, press the AUDIO button

repeatedly to select the sound mode of the MONO L, MONO R, and Stereo,

no language function.

5.12 Change the Video Signal System

During playback of DVD/VCD disc, press the P/N button on the front panel

repeatedly to change the VIDEO SIGNAL SYSTEM mode as follows:

--> PAL--> AUTO --> NTSC -->

5.13 Look over the Playback Status

1. In the state of DVD disc playing, press the OSD button repeatedly on the

remote controller to turn on/off the playback status. When it is on, it will

display the information such as: the serial number of the playing title, the

serial number of the playing chapter, the elapsed time of the playing chapter,

the remained time of the playing chapter, the elapsed time of the playing title,

the remained time of the playing title, etc.

2. In the state of VCD/MP3/WMA/CD disc playing, press the OSD button

repeatedly on the remote controller to turn on/off the playback status. When

it is on, it will display the information such as: the serial number of the playing

track, the elapsted time of the playing track, the remained time of the playing

track, the elapsted time of the disc, the remained time of the disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marquant mcr-1290 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info