Bedienungsanleitung Matrix T50x (Seite 4 von 11) (Englisch)

664315

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

4 5

2.4 ADJUSTING THE BELT

After placing the treadmill in the position it will be used, the belt must be

checked for proper tension and centering. The belt might need to be

adjusted after the first two hours of use. Temperature, humidity, and use

cause the belt to stretch at different rates. If the belt starts to slip when a

user is on it, be sure to follow the directions below.

Locate the two hex head bolts on the rear of the treadmill.

The bolts are located at each end of the frame at the back of

the treadmill. These bolts adjust the rear belt roller. Do not

adjust until the treadmill is on. This will prevent over

tightening of one side.

The belt should have equal distance on either side between

the frame. If the belt is touching one side, do not start the

treadmill. Turn the bolts counter clockwise approximately one

full turn on each side. Manually center the belt by pushing

the belt from side to side. Tighten the bolts the same amount

as when the user loosened them, approximately one full turn.

Inspect the belt for damage.

While the treadmill is running at 5 kph, observe the belt

position. If it is moving to the right, tighten the right bolt by

turning it clockwise ¼ turn, and loosen the left bolt ¼ turn.

If it is moving to the left, tighten the left bolt by turning it

clockwise ¼ turn and loosen the right ¼ turn. Repeat Step 3

until the belt remains centered for several minutes.

Check the tension of the belt. The belt should be very snug.

When a person walks or runs on the belt, it should not

hesitate or slip. If this occurs, tighten the belt by turning

both bolts clockwise ¼ turn. Repeat if necessary.

STEP 1

STEP 2

STEP 3

STEP 4

CHAPTER 2: Preventative maintenance CHAPTER 3: Serial number location

T50x, T50x-U TREADMILL

SERIAL #

PLACEMENT

CHAPTER 4: overlay and Workout description

4.1 T50x CONSOLE DESCRIPTION

1/4 TURN

WORKOUT KEYS: Simple program view and selection buttons.

qUICK START: One touch Start and Quick Start.

ENTER: To confirm each program setting.

UP/DOWN INCLINE: Easy information and incline selection.

UP/DOWN SPEED: Easy information and speed selection.

EMERGENCY STOP / IMMOBILIzATION: To stop all functions and immobilize the unit. The emergency stop on this treadmill must be returned to its original

position in order to allow normal operation of the unit.

STOP: Ends workout and shows workout summary data.

COOL DOWN: Puts treadmill into Cool Down mode. Cool Down time is dependent on the length of the workout. Workouts 19 minutes and shorter will have a

cool down length of 2 minutes. Workouts 20 minutes and longer will have a cool down length of 5 minutes.

CLEAR: Use the CLEAR key to clear data not yet entered during the workout setup.

NUMBER KEYS: Press the numbers to input exercise Time, Weight, Level, Age, Heart Rate, Speed and Incline.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Matrix T50x Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info