Bedienungsanleitung Maxdata SN 40 (Seite 77 von 85) (Englisch)

650496

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

76 77MAXDATA SN 40 M1 – User GuideProtecting Local Disks

7. When you are prompted to restart the computer, click “Yes”.

You do not have to restart your computer immediately, but you cannot access the recovered

disk or partition until you do.

As soon as you restart the computer, you must start Intel

Client Backup and Recovery and

back up the recovered disk or partition manually (as described in “Manually Backing up Your

Disk” on page 72) to resume protection. In addition, if you recovered a partition and any other

partitions on the same disk were protected, you must manually back up those partitions as

well.

Recovering a System Disk or Partition

To recover a system disk or partition using the recovery CD:

1. Using the appropriate procedure for your system, configure the computer to boot from the CD-

ROM drive.

2. Insert the recovery CD into the CD-ROM drive.

When responding to the prompts, use the arrow keys to highlight the desired item, use the

space bar to select or clear options (an X appears in the brackets when the option is selected),

and press Enter to make your selection. You can also tab between fields.

Arrow keys Navigate between items and

highlight items

Space bar Select or clear options

Enter Make a selection

Tab Move between fields

3. When the hardware list appears, use the arrow keys to select the network interface card (NIC)

that you want to use when recovering the data, and then select “Next”.

In most cases, there will be only one NIC, and you can simply select “Next”.

This screen displays only the NICs on this system that are supported by Client Backup and

Recovery. If no NICs appear on this screen, you might need to install an appropriate network

driver. Select “Load Driver”, select the location from which you want to install the driver

(“Load From System” for the local hard disk, “Load From Floppy” for a floppy disk drive, or

“Load From CDROM” for a CD-ROM drive), insert the disk in the drive (if loading from a floppy

disk or CD-ROM), and respond to the prompts. For information about obtaining the appropriate

driver, contact your vendor.

To see a complete list of the detected hardware, select “Rescan”. When you are done viewing

the list, select “OK”.

4. Review the settings for your NIC and select “Next”.

The recovery CD obtains the IP address to use from your DHCP server. If the displayed

settings are not the ones you want to use, or if no IP address is displayed, use the arrow

keys and space bar to select “Config” and then type in the desired IP address (for example,

“192.168.0.101”) or subnet mask. (If you make a mistake typing either the IP address or

subnet mask, select “Disable” to clear the displayed information.) Then select “OK” and select

“Next”.

5. In the “Client Name” field, enter the full computer name of this computer in all capital letters.

If you don’t remember the full computer name, access the Manager (as described in

“Accessing the Manager” on page 15) and click “Backups” in the navigation bar. In the

“Protected disks” list, the “Computer Name” column lists the computer name of each

computer that has backed up disks to the storage system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Maxdata SN 40 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info