Bedienungsanleitung Metabo Multi 310G (Seite 19 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

always work with a properly set riving

knife.

Do not jam workpieces.

Cut thin or thin-walled workpieces only

with fine-toothed saw blades. Always

use sharp saw blades.

If in doubt, check workpiece for inclusion

of foreign matter (e.g. nails or screws).

Drawing-in/trapping hazard!

Ensure that no parts of the body or cloth-

ing can be caught and drawn in by rotat-

ing components (no neckties, no loose-

fitting clothes; contain long hair with hair-

net).



Hazard generated by insuffi-

cient personal protection gear!

Wear hearing protection.

Wear safety glasses.

Wear dust mask if work generates dust.

Wear suitable work clothes. When work-

ing outdoors wearing of non-slip shoes is

recommended.



Risk of injury by inhaling wood

dust:

Dust of certain timber species (e.g. oak,

beech, ash) can cause cancer when

inhaled: Always use a dust collector. The

dust collector must meet the following

requirements:

− fitting the outer diameter of the suc-

tion port

− air volume ≥ 550 m

/h;

− vacuum at suction port of machine

≥ 740 Pa;

− air speed at suction port of machine

≥ 20 m/s.



Hazard generated by modifica-

tion of the machine or use of parts

not tested and approved by the equip-

ment manufacturer!

Assemble electric tool in strict accord-

ance with these instructions.

Use only parts approved by the equip-

ment manufacturer.

Do not make changes to any of the

parts.

Use only cutting tools according to

EN 847-1.

Use only matching saw blades and riving

knives.



Hazard generated by electric

tool defects!

Keep electric tool and accessories in

good repair. Observe the maintenance

instructions.

Check electric tool for possible damage

before any use: Before operating the

electric tool all safety devices, protection

devices or slightly damaged parts must

be inspected for proper functioning as

specified. Check to see that all moving

parts work properly and do not jam. All

parts must be correctly installed and

meet all conditions necessary for the

proper operation of the electric tool.

Damaged protection devices or parts

must be repaired or replaced by an

qualified specialist. Have damaged

switches replaced by a service centre.

Do not operate electric tool if the switch

can not be turned ON or OFF.

Keep handles free of oil and grease.

2.3 Symbols Used Through-

out These Instructions



Danger!

Indicates risk of personal

injury or severe material

damage.



Risk of electric shock!

Risk of personal injury by elec-

tric shock.

Danger! Drawing-in/trapping

hazard!

Risk of personal injury by body

parts or clothing being drawn

into the rotating saw blade.



Caution!

Risk of material damage



Note:

Supplementary information

• One machine – four operating

modes:

− surface planer

− thicknesser

− circular saw

− spindle moulder

• Wide range of accessories.

• Latest technology for perfect per-

formance.

4.1 Machine installation

1. Transport combination machine on

the pallet to a suitable location:

− Floor space required

at least 3 m x 4 m.

Depending on workpiece dimen-

sions the required space may be

more.

− sufficient load bearing capacity

− level

− even

− dry

− non-slip.

2. Remove packing and enclosed

parts.

3. Unscrew and remove the metal

clamps holding the combination

machine on the pallet.

4. Lead carrying straps though under-

neath the combination machine at

the marked locations (1).

5. Lift combination machine off the pal-

let.



Danger!

The combination machine can

turn over while being carried! Take

care to keep the machine balanced

while carrying it.



Caution!

Lift the machine only at the

locations mentioned in this manual.

Other components are not designed

for the tensile load by the machine

weight.

4.2 Mains Connection



Danger! Electrical hazard.

Operate in dry environment

only.

Operate machine only on a power

source matching the following

requirements (see also "Technical

Specifications"):

− protected by a residual current

operated device of 30 mA capa-

city;

− outlets properly earthed;

− 5-wire three-phase outlets with

neutral lead.

− when a dust collector is used it

must also be properly earthed.

Position power supply cable so it

does not interfere with the work and

is not damaged.

Protect power supply cable from

heat, aggressive liquids and sharp

edges.

Use only extension cables of suffi-

cient lead cross-section.

Do not pull on power supply cable to

unplug.



Check direction of rotation!

(machines with 3-phase motor

only):

Depending on the phase sequence it

is possible that the motorshaft will

turn in reverse rotation. This can

cause damage to the machine and

workpiece. It is therefore necessary

to check the direction of rotation after

each connection to a different power

3. Special Product Features

4. Transportation and

Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 310G Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info