Bedienungsanleitung Metabo Multi 310G (Seite 21 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

6.2 Safety

Safety Devices

• Cutterblock guard

The cutterblock cover prevents the rotat-

ing cutterblock from being touched when

surface planing.

For effective protection the cutterblock

cover must always be adapted to the

workpiece.

Information for a safe operation



Risk of kickback!

Risk of injury by workpiece

kickback (workpiece is caught by the

rotating cutterblock and thrown back

against the operator):

− Always use sharp cutter knives.

− If in doubt check workpiece for inclu-

sion of foreign objects (e.g. nails,

screws, lose knots).

− Always plane the workpiece over its

full length.



Risk of injury by touching the

rotating cutterblock:

− always keep your hands well clear

of the cutterblock.

− When jointing, use the jointer

fence to provide firm support for

the workpiece. Use an auxiliary

fence when planing thin or nar-

row stock, to keep your hands at

a safe distance from the cutter-

block.

− Always cover the part of the cutter-

block that is not covered by the

workpiece with the cutterblock

cover.

− Adjust the cutterblock cover exactly

to the dimension of the workpiece.

− Never reach with your hands under

the cutterblock cover when guiding

the workpiece!

− Use workpiece supports (such as

table extensions) to keep long

stock from losing its balance.

− Plane only stock which rests

securely on the table.

− Use a feeding aid (push block) when

planing a small workpiece, which

can not be guided with a sufficient

safety distance to the cutterblock.

− Do not pull the workpiece back over

the unguarded cutterblock!



Risk of injury by cuts with cut-

terblock at standstill:

− Always cover the cutterlock with the

guard extrusion of the cutterblock

cover when the machine is not used

as thickness planer.

6.3 Operation

1. Place stock against the jointer fence

(16).

2. Adjust cutterblock guard extrusion

(17):

− Planing the face of a plank or work-

pieces up to 75 mm thick:

Use the adjusting screw (18) to

adapt the guard extrusion to the

height of the workpiece. When guid-

ing the workpiece the hands slide

over the guard extrusion.

− when planing narrow edges (edge

jointing) or workpieces more than

75 mm thick:

Loosen adjusting screw (19) to

adapt the guard extrusion to the

width of the workpiece.

3. Setting the planing thickness at the

infeed table (20):

Loosen locking screw (21);

set planing thickness with the regu-

lating screw (22).

4. When planing thickness is set,

tighten locking screw (21).

5. Height adjustment of outfeed table

(23):

Loosen locking screw (24);

Set cutter knife setting gauge (26)

as illustrated in direction of arrows

on the outfeed table (27);

The edge (28) of the setting gauge

must fit closely to the edge of the

outfeed table;

adjust height position of the outfeed

table with the regulating screw (25)

– the setting is correct when the cut-

ter knife (29), at the highest point,

barely touches the setting gauge.

6. When the outfeed table is adjusted,

tighten locking screw (24).

7. Set operating mode selector to

planer/thicknesser mode.

8. Start motor.

9. Assume proper operating position:

position yourself to one side of the

infeed table.

10. Feed workpiece straight across the

infeed table. Holding your fingers

close together, guiding the work-

piece with the palm of your hands.

11. Switch machine off if no further plan-

ing is to be done immediately after-

wards.

21 22

2425

26 28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 310G Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info