Bedienungsanleitung Metabo Multi 310G (Seite 20 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

outlet. To do so, start the circular saw

briefly and check to see if the saw

blade turns in the direction indicated

by the arrow.

With an incorrect direction of rota-

tion, the phase sequence needs to be

corrected by a qualified electrician at

either the power outlet or the power

cable.

Main switch



Note:

The main switch (2) can be

blocked by a padlock to prevent unau-

thorized use.

To switch ON:

• Turn main switch (2) to "1".

To switch OFF

• Turn main switch (2) to " 0".

Operating mode selector

The operating mode selector (3) is actu-

ated by the key supplied. The following

operating modes can be selected:

A = Spindle moulder mode

B = Planer/thicknesser mode

C = Circular saw mode

Start/stop pushbuttons

For each operating mode separate start/

stop pushbuttons are provided.

• To switch ON:

Press the green pushbutton of the

respective operating mode.

• To switch OFF:

Press red pushbutton – each oper-

ating mode can be switched OFF by

any of the three red pushbuttons or

by the main switch.

5.1 General safety devices

Emergency-stop pushbutton

In spindle moulder mode, the red push-

button (4) functions as emergency stop

switch. In any operating mode the emer-

gency stop switch immediately shuts the

machine down. Before switching ON

again, the red pushbutton needs to be

reset by turning it counter-clockwise.

Undervoltage relay

An undervoltage relay trips in the event

of a voltage failure to prevent restarting

of the machine when the power is

restored. To switch ON again, the green

pushbutton of the relevant operating

mode must be actuated.

6.1 Setup



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Work area preparation

Ensure the removal of all not required

objects from the work area:

1. Saw blade and blade guard fully

retracted and covered by table

insert?

2. Cutter fence completely dis-

mounted?

3. Cutter spindle fully retracted and

covered by table rings and insert?

4. Dust chute swung under the planing

bed for thickness planing?

5. Planing beds folded down?

6. Morticing bit chuck covered?

Fence installation

1. Place the fence carrier (5) on the

guide bar (6) and secure with the

star-knob screw (7).

2. Loosen lock lever (8) and adjust

jointer fence position lengthwise: the

recess in the fence extrusion (9)

must be positioned over the cutter-

block, as illustrated below.

3. Cover the part of the cutterblock

behind the jointer fence with the

cover plate (10).

Cutterblock cover installation:

1. Fasten the cutterblock's arm (11) to

the outfeed table.

2. Slide cutterblock guard extrusion

(12) in the seat on the arm of the

cutterblock cover and lock with

screw (13).

Connecting the dust collection

attachment

1. Unlock the infeed table (14) and

carefully lift it up.

2. Hang the dust chute for surface

planing with both prongs on the cut-

terblock guard plate.

3. Pull locking bolt on hinge of infeed

table out and carefully lower the

infeed table.

4. Connect a suitable dust collector to

the dust chute's suction port (15).

5. Operating Elements

6. Surface Planer Mode

76 8

12 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 310G Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info