Bedienungsanleitung Metabo Multi 310G (Seite 22 von 64) (Deutsch, Englisch, Holländisch, Dänisch)

451464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

Workpiece dimensions

• Width: max. 309 mm.

• Thickness: at least 4 mm more than

the set planing thickness.

Tips and Tricks

• Plane stock with the grain, if possi-

ble.

• Use roller supports on both sides of

the planer/thicknesser when work-

ing long stock.

• It is better to make several passes

with less chip removal, than making

only a few passes with a high depth

of cut.

• When surface planing a warped

(twisted) board, place on infeed

table with the hollow side facing

down.

• When surface planing short work-

pieces:

− use push stick;

− feed workpiece with the small

face first;

− guide workpiece turned approx.

20° against the direction of feed.

• Keep surfaces of planing beds clean

– in particular, remove resin residue

with a suitable cleaning and mainte-

nance spray (optional accessory).

• Apply an anti-seize compound to all

planing bed surfaces afterwards.

This makes feeding easier and pro-

vides for a smoother surface finish.

7.1 Setup



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Work area preparation

Ensure the removal of all not required

objects from the work area:

1. Saw blade and blade guard fully

retracted and covered by table

insert?

2. Saw set to 45 ° bevel tilt and

locked?

3. Cutter fence completely dis-

mounted?

4. Cutter spindle fully retracted and

covered by table rings and insert?

5. Morticing bit chuck covered?

Connecting the dust collection

attachment

1. Unlock the infeed table (30) and

carefully lift it up.

2. Remove the dust chute for jointing.

3. Unlatch the locking lever (31) under

the outfeed table (32) and carefully

swing outfeed table open.

4. Swing dust chute for thickness plan-

ing (33) up and let engage.

5. Connect a suitable dust collector to

the dust chute's suction port.

7.2 Safety

Safety Devices

• Safety switches

Three limit switches prevent the cutter-

block from being driven, unless the cut-

terblock is covered by the planing beds

or the dust chute.

• Anti-kickback lock

The anti-kickback lock (underneath the

dust chute for thickness planing (33))

prevents the workpiece from being

thrown back against the operator by the

rotating cutterblock.

All fingers of the anti-kickback lock must

end in a point on the underside.

All anti-kickback fingers must automati-

cally return to their rest position (down-

wards).

Information for a safe operation

Danger! Drawing-in/trapping

hazard!

− Never reach with your hands into

the machine when guiding the work-

piece!

− Use a feeding aid (push stick) if you

want to feed short stock into the

thicknesser. Stock to be thicknessed

must be at least 200 mm long.

− Guide a workpiece on the outfeed

side if it has been fed so far into the

thicknesser that it can no longer be

safely guided from the infeed side.

− Remove stuck stock only after motor

has come to a complete stop and

the machine is unplugged.



Risk of kickback!

Risk of injury by workpiece

kickback (workpiece is caught by the

rotating cutterblock and thrown back

against the operator):

− Do not jam workpieces.

− Operate machine only with a fully

functional anti-kickback lock.

− Always use sharp cutter knives.

− If in doubt check workpiece for inclu-

sion of foreign objects (e.g. nails,

screws, lose knots).

− Always plane the workpiece over its

full length.

− Do not thickness plane more than

two workpieces at the same time.

7.3 Operation

1. Loosen locking screw (34) and set

planing thickness with the hand-

wheel (35).

− The thicknesser bed adjusts in a

range from 5 mm to 200 mm.

− One full revolution of the handwheel

moves the thicknesser bed by

6,3 mm.

2. Tighten locking screw (34) again.

3. To thickness plane stock which sur-

faces are not parallel, use suitable

feeding aids (make fitting tem-

plates).

4. Set operating mode selector to

planer/thicknesser mode.

5. Start motor.

6. Assume proper operating position:

to feed the workpiece into the

machine, position yourself offset to

one side of the feed opening.

7. Thickness Planer Mode

34 35

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo Multi 310G Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info