Bedienungsanleitung Metabo TP 7500 SI (Seite 11 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Finnisch)

600858

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

 Unplug the pump and allow

to cool. A specialist must

check the system to make

sure it is in perfect working

order before it can be used

again.

Danger! Risk of electric

shock!

 Do not touch the plug with

wet hands! To unplug

always pull at the plug, not

the power cable.

 Connect only to an earthed

outlet that is properly

installed, earthed and

tested. Mains voltage and

fuse protection must corre

spond to those stated in the

"Technical Specications".

 Protection must be pro-

vided by a residual current

device (RCD) of max.

mA capacity.

 The earthed outlet or the

plug connection to an

extension cable must be

located in an area safe

against flooding.

 Use only extension cables

of sufficient lead cross sec

tion (see "Technical Specifi-

cations"). Unroll cable reels

fully.

 Do not buckle, squeeze,

drag or drive over power

cable and extension cables;

protect from sharp edges.

 Place extension cable so

that it can not get into the

fluid to be pumped.

 Unplug:

 prior to all servicing;

 when persons are in the

swimming pool or garden

pond.

Danger by pump fail-

ures!

 If you notice shipping dam-

age while unpacking, notify

your supplier immediately.

Do not operate the

machine!

 Before each use check the

pump, especially the power

cable and plug for possible

damage. Risk of fatal elec

tric shock!

 A damaged pump must be

workmanlike repaired

before it can be used again.

 Do not attempt to repair the

pump yourself! When

repaired inexpertly there is

a hazard of fluid entering

the electrical parts of the

pump.

Caution!

To avoid water damage,

e.g. flooded rooms, caused

by pump malfunctions or

defects:

 provide for suitable safety

measures such as the fol

lowing:

 alarm or

 collection tank with moni-

toring.

The manufacturer is not liable

for any damage caused by:

 improper use of the pump;

 overloading of the pump

through continous opera

tion;

 failure to operate and store

the pump in a frost-free

environment;

 unauthorised modification

of the pump (repairs to

electrical equipment may

only be carried out by quali

fied electricians!);

 use of spare parts which

have not been tested and

approved by the manufac

turer; or

 use of unsuitable installa-

tion materials (fittings, con-

nection lines etc.).

Suitable installation materi-

als:

 pressure-resistant (min.

10 bar)

 heat-resistant (min.

100°C).

5.1 Discharge hose connec-

tion

The discharge hose is connected either

directly to the discharge port (10), or by

means of the multi-adapter (11) (secure

discharge hose with hose clamps, if nec-

essary).

The check valve's flap (12) must open in

the direction indicated by the arrow. (The

marking "UP" must face the multi adap

tor).

Note:

When using the multi adaptor cut

off any parts nor required, as they

reduce the flow unnecessarily.

5.2 Installation

 Space required approx. 20 cm x

20 cm.

 The pump must not be submerged

deeper into water then stated in the

“Technical Specifications”.



Place pump so that the suction inlet

can not be blocked by foreign objects

(stand on a base, if necessary).

 Ensure sufficient upright stability.

Caution! 

Do not lift pump at cable or dis-

charge hose; both are not designed

for the tensile load by the weight of

the pump.

 Lower pump to the bottom of the

fluid container. Use a strong rope,

fastened to the handle/hanger to

lower the pump.



The pump can also be operated

when suspended by a rope.

Any possibly present air cushion in

the pump can escape through vent

holes when the pump is lowered into

the fluid. Venting generates air bub

bles. This is no fault of the pump but

the effect of automatic venting.

When using the pump for the first

time it may take several seconds

before the air is vented.

 To start the submersible pump plug

power cable in.

 Unplug to stop the pump.

5. Prior to Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TP 7500 SI Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info