Bedienungsanleitung Metabo TP 7500 SI (Seite 12 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Finnisch)

600858

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

Before plugging in set the operating

mode with the Mode selector

(13):

Position A = Automatic mode

Position M = Manual mode

6.1 Automatic mode

In Automatic mode the submersible

pump is automatically started and

stopped by the integrated float switch:

 The pump starts pumping when the

float switch is raised by the fluid

above the starting level (14).

 The pump stops when float switch

falls to below the cut-out level (15).

Caution! 

The float switch must be able

to move in such way that the pump

can not run dry.

6.2 Manual mode

Starting

 Push Mode selector (13) up to posi-

tion M. The pump starts pumping.

Caution! 

Do not let run pump unat-

tended in Manual mode. Risk of dam-

age by pump running dry at low fluid

levels.

Stopping

Contrary to Automatic operation the

pump does not stop running when a cer-

tain water level is reached.

 Push Mode selector (13) down into

position A. The pump stops when

the float switch lowers to below the

cut-out level .

Danger! 

Prior to all servicing:

 Switch Off.

 Unplug.

Service and repair work other than

described here must be left to quali

fied specialists.

7.1 Periodic maintenance

For the pump to function perfectly at any

time periodic maintenance is required.

This also applies if the pump is used

under heavy conditions, but does not run

for extended periods of time (e.g. when

used in well drains).

Yearly service

1. Check pump casing, cables and

float switch for damage.

2. Rinse pump with clear water.

Remove persistant soiling, e.g.

algae desposits, with brush and

dishwashing liquid.

3. To flush the inside of the pump,

place it into a container filled with

clear water and switch ON briefly.

Rinsing the pump.

 Always rinse the pump with clear

water when liquids were pumped

that leave residues, such as chlor

ous water from a swimming pool.

Cleaning the float switch

1. Set Mode selector (16) to position

"O", then press and hold the selec-

tor to unlock the float cover (17).

Remove float cover.

2. Unhook float (18) complete with

shaft (19) and clean.

3. Clean walls and floor of float com-

partment.

4. Reassemble pump.

Cleaning the intake port's cover

1. Loosen screws (20) and remove the

cover.

2. Clean impeller and all accessible

inside surfaces of the casing.

Remove any fibres which may have

wound around the impeller shaft.

Remove persistant soiling with

brush and dishwashing liquid.

3. Reassemble pump.

7.2 Pump storage

Caution! 

Frost damages the pump and

accessories, as both always contain

water!

 When there is danger of freezing

remove pump and accessories and

store in frost-free location.

Danger! 

Prior to all servicing:

 Switch OFF.

 Unplug.

6. Operation

7. Care and Maintenance

8. Trouble Shooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TP 7500 SI Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info