Bedienungsanleitung Midas M32 (Seite 20 von 61) (Englisch)

658461

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

20 M32 DIGITAL CONSOLE User Manual

4. When you have assigned all of the desired channels to the mute group,

release the dedicated Mute Group button.

NOTE: The individual channel MUTE buttons will remain fully functional during

the assignment process, only the mute group buttons are blocked.

To use the MUTE GRP screen to mute or unmute the groups, perform the

following steps:

1. Tap any of the six push encoders to mute the corresponding group, and thus

mute all channels that are assigned to that mute group.

2. Tap the push encoder of a currently-muted group to unmute the mute

group.

3. When nished working with mute groups, tap the MUTE GRP screen

selection button to exit the MUTE GRP screen. The entire screen will again

display its full set of controls for the current page.

2. Main Display

2.1 Main Display - Top Section

The top section of the Main Display permanently covers useful status

information. The top left corner shows the selected channel number, its user-

assigned name and the selected icon. The next block shows the current scene

number and name in amber, as well as the next upcoming scene. The centre

section displays the playback le name along with elapsed and remaining time,

and a recorder status icon. The next block to the right has four segments to

show the status of the AES50 ports A and B, the Card slot, and the audio clock

synchronisation source and sample rate. Small green square indicators show

proper connectivity. The rightmost block shows the console time, which can be

set under Setup - Cong.

2.1.1 Home

The HOME screen contains a high-level overview of the selected input or output

channel, and oers various adjustments not available through the dedicated

top-panel encoders.

The HOME screen is divided into the following tabs:

home: General signal path for the selected input or output channel.

cong: Allows selection of signal source/destination for the channel,

conguration of insert point, and other settings.

gate: Controls and displays the channel gate eect beyond those oered by

the dedicated top-panel encoders.

dyn: Controls and displays the channel dynamics eect (compressor) beyond

those oered by the dedicated top-panel encoders.

eq: Controls and displays the channel EQ eect beyond those oered by the

dedicated top-panel encoders.

sends: Controls and displays the channels sends, such as sends metering and

sends muting.

main: Controls and displays the selected channel’s output.

home

The home tab of the HOME screen displays a general signal path for the currently

selected input or output channel. It visually displays various parameters of the

input, gate, insert point, EQ, dynamics, output path and buses.

The home tab contains the following parameters (divided into two pages)

that can be adjusted using the six push encoders.

Page 1

1. Turn the rst push encoder to adjust the input gain (trim) of

thechannel.

2. Tap the rst encoder to link the channel with its adjacent channel.

3. Adjust the second encoder to set the threshold of the channel

noisegate.

4. Tap the second encoder to toggle the channel noise gate in/out of the

signal path.

5. Adjust the third encoder to toggle the channel’s insert point between

pre-fader and post-fader status.

6. Tap the third encoder to toggle the channel insert in/out of the

signalpath.

7. Adjust the fourth encoder to toggle the channel dynamics between

pre-EQ and post-EQ status.

8. Tap the fourth encoder to toggle the channel EQ in/out of the

signalpath.

9. Adjust the fth encoder to set the threshold of the channel compressor.

10. Tap the fth encoder to toggle the channel compressor in/out of the

signal path.

11. Adjust the sixth encoder to pan the selected channel within the main

stereo output.

12. Tap the sixth encoder to assign the selected channel to the main

stereooutput.

Page 2

1. Adjust the rst push encoder to select the console channel currently

controlled by the HOME screen.

2. Tap the rst encoder to toggle +48V phantom power on/o for the

currently selected input.

3. Tap the second encoder to toggle the phase ip on/o for the currently

selected channel.

4. Adjust the third encoder to select to which of the eight DCA groups the

currently selected channel will be assigned.

5. Tap the third encoder to assign the currently selected channel to the

selected DCA group.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas M32 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info