Bedienungsanleitung Midas M32 (Seite 21 von 61) (Englisch)

658461

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

21 M32 DIGITAL CONSOLE User Manual

6. Adjust the fourth encoder to select to which of the six mute groups the

currently selected channel will be assigned.

7. Tap the fourth encoder to assign the currently selected channel to the

selected mute group.

8. Tap the fth encoder to toggle solo on/o for the currently

selectedchannel.

9. Turn the sixth encoder to adjust the fader level for the currently

selectedchannel.

10. Tap the sixth encoder to toggle mute on/o for the currently

selectedchannel.

cong

The conguration tab allows selection of signal source/destination for the

channel, conguration of insert point, and other settings, as well as conguration

of the channel delay.

The cong tab of input channels 1-32 contains the following parameters

that can be adjusted using the six push encoders:

1. Turn the rst push encoder to adjust the input gain (trim) of

thechannel.

2. Tap the rst encoder to allow linking of the channel to the

adjacentchannel.

3. Adjust the second encoder to set the low-cut frequency of the channel.

4. Tap the second encoder to toggle the low-cut lter in/out of the

signalpath.

5. Adjust the third encoder to scroll among all of the possible sources for

the channel.

6. Tap the third encoder to select the currently highlighted source and

assign it to the channel.

7. Adjust the fourth encoder to set the amount of digital line delay applied

to the channel.

8. Tap the fourth encoder to toggle the delay in/out of the signal path.

9. Adjust the fth encoder to toggle the channel insert between pre- and

post-EQ/compressor.

10. Tap the fth encoder to toggle the channel insert in/out of the

signalpath.

11. Adjust the sixth encoder to scroll among the signal path choices for the

insert point.

12. Tap the sixth encoder to assign the selected signal path to the

insertpoint.

NOTE: Mix Bus channels do not have Gain, Low Cut, Phantom, Phase, Source

and Delay. But they do have a macro feature for setting all channel send taps to

the selected bus at once. As an example, this can be used for switching all sends

from Pre Fader to Post Fader or for ensuring that all channel taps are consistent.

gate

The gate tab displays all aspects of the channel noise gate, and allows for very

deep control of the gate eect. Whereas the top panel’s dedicated GATE section

allows control of the gate’s threshold and in/out status, the gate tab oers many

more controls. This tab can be accessed directly by pressing the VIEW button in

the top panel GATE section.

The gate tab contains the following parameters, divided among two pages,

that can be adjusted using the six push encoders:

Page 1

1. Adjust the rst push encoder to set the input threshold of the gate.

2. Tap the rst encoder to toggle the noise gate in/out of the signal path.

3. Adjust the second encoder to set the range of a ‘ducking eect applied

to the channel.

4. Tap the second encoder to toggle the ducker eect in/out of the

signalpath.

5. Adjust the third encoder to set the attack time of the onset of the noise

gate eect.

6. Adjust the fourth encoder to set the hold time of the noise gate eect.

7. Adjust the fth encoder to set the release time of the noise gate,

controlling how quickly the gate opens up and lets the signal through.

Page 2

1. Push encoders 1 & 2 function the same on pages 1 & 2.

2. Adjust the fourth encoder to set the frequency of the key lter that can

be used to trigger the noise gate.

3. Tap the fourth encoder to toggle the key lter on/o, allowing a specic

frequency to control the gate.

4. Adjust the fth encoder to set the steepness of the EQ slope used in the

key lter.

5. Tap the fth encoder to send the key source to the solo bus, allowing

the key source to be monitored and evaluated.

6. Adjust the sixth encoder to select the specic key source to be used.

Choices include ‘Self’ (the channel’s own signal), as well as any other

input/output of the console.

7. Tap the sixth encoder to assign the selected key source to the gate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas M32 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info