Bedienungsanleitung Midas M32 (Seite 26 von 61) (Englisch)

658461

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

26 M32 DIGITAL CONSOLE User Manual

• AES50A 1-2

• AES50A 1-4

• AES50A 1-6

• AES50B 1-2

• AES50B 1-4

• AES50B 1-6

• Card 1-2

• Card 1-4

• Card 1-6.

out 1-16

The ROUTING screens out 1-16 tab allows the user to patch the M32’s various

internal signal paths to the 16 analogue XLR outputs that are located on the

console’s rear panel.

The M32 allows for many dierent kinds of output signal paths, and this screen

is where these outputs are assigned to a physical rear panel output, so that the

signal path can be patched to their eventual destination, such as front-of-house

PA speakers or a powered stage monitor.

To assign the various output paths to the rear panel XLR outputs, perform the

following steps:

1. Adjust the rst push encoder to select to which of the 16 rear panel analogue

outs you wish to assign an output signal path.

2. Adjust the third encoder to select an output path category. These include:

• O

• Main (LRC) Mix

• Mix Bus Outputs

• Matrix Outputs

• Direct Outs

• Monitor.

3. Adjust the fourth encoder to select a specic output path, including:

• O

• Main L

• Main R

• Main C/M

• Any of the 16 Mix Outputs

• Any of the six Matrix Outputs

• Any of the 32 Direct Outputs

• Any of the eight Auxiliary Outputs

• Any of the FX Direct Outputs

• Monitor L

• Monitor R

• Talkback.

4. Tap the fourth encoder to assign the selected output path,

completingtheprocess.

5. Adjust the fth encoder to select the signal tap point for the output

assignment. This determines where in the audio signal path the source is

‘tapped’ as it is sent to the physical rear panel output. The available signal

tap points include:

• IN/LC

• IN/LC +M

• PreEQ

• PreEQ +M

• PostEQ

• PostEQ +M

• PreFdr

• PreFdr +M

• Post Fader.

6. Tap the fth encoder to assign the selected signal tap point.

7. Turn the sixth encoder to adjust the amount of digital line delay applied to

the output path as it is sent to the rear panel physical output. As the amount

of delay is adjusted, the current delay time is displayed in three dierent

units of measurement: feet, metres and milliseconds.

8. Tap the sixth encoder to toggle delay on/o. The Delay label illuminates

when the delay is inserted into the signal path.

TIP: Applying a delay to an output signal is typically done when the console is

used in a ‘multi-zone’ PA speaker setup, where some PA speakers are located

near the stage, and a second set of speakers is located further back within the

audience. By applying an appropriate amount of delay only to the speakers

located near the stage, the audience hears the audio from all speakers at

the same time, ensuring maximum time-alignment and sound quality. The

M32 assumes an operating temperature of 20°C/68°F when calculating the

delaytimes.

aux out

The ROUTING screen’s aux out tab allows the user to patch an internal signal

path (such as a mix output used as an eects send) to the six separate ¼"/RCA

auxiliary outputs.

Since these six outputs can have a wide variety of signal paths assigned to them,

they can be used for a wide variety of tasks, such as:

1. Feeding an external eects processor when the internal eects

areinsucient.

2. Patching a specic console signal path to an outboard recorder.

3. Feeding the analogue or digital audio inputs of a nearby video recorder.

To make an assignment as described above, perform the following steps:

1. Adjust the rst push encoder to select to which auxiliary outputs to assign a

source. Choices include

• Aux Out 1

• Aux Out 2

• Aux Out 3

• Aux Out 4

• Aux Out 5

• Aux Out 6

• AES/EBU (Digital) Out L

• AES/EBU (Digital) Out R.

2. Adjust the third encoder to select for coarse range:

• Insert

• Main (LRC)

• Mix Bus

• Matrix

• Direct Out

• Monitor.

3. Adjust the fourth encoder to select a specic signal path to feed the selected

physical output. Choices include:

• Insert Point

• Main L

• Main R

• Main C/M

• Any of the 16 Mix Outputs

• Any of the six Matrix Outputs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas M32 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info