Bedienungsanleitung Midas M32 (Seite 27 von 61) (Englisch)

658461

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

27 M32 DIGITAL CONSOLE User Manual

• Any of the 32 Direct Outputs

• Any of the eight Auxiliary Outputs

• Any of the FX Direct Outputs

• Monitor L

• Monitor R

• Talkback.

4. Tap the fourth encoder to assign the selected output path, completing the

process.

5. Adjust the fth encoder to select the signal tap point for the output

assignment. Choices include:

• IN/LC

• IN/LC +M

• PreEQ

• PreEQ +M

• PostEQ

• PostEQ +M

• PreFdr

• PreFdr +M

• Post Fader.

6. Tap the fth encoder to complete the signal tap point assignment.

p16 out

The ROUTING screen’s p16 out tab allows the user to route various console signal

paths to the rear panel P16 Ultranet output. This output allows for 16 channels

of audio to be sent, in digital form, to various accessories such as a personal

monitoring distribution box.

Using the p16 out routing screen, the user can congure the P16 output to carry

not only the main LR mix, but also various audio ‘stems’ of audio material sources

from a bus send mix, such as a stereo drum mix, stereo keyboards, guitars,

bass, vocals, etc. Musicians on stage would then be free to each craft their own

personal mix of these musical stems, all delivered from the FOH position to stage

over a single Ethernet cable.

To select which audio signals are sent to the P16 bus, perform the

followingsteps:

1. Adjust the rst push encoder to select for which of the 16 channels in the P16

bus you wish to select an audio source.

2. Adjust the third encoder to select a category of audio source to send to the

currently selected P16 channel. These categories include:

• Insert

• Main (LRC)

• Mix Bus

• Matrix

• Direct Out

• Monitor.

3. Adjust the fourth encoder to select which specic signal path to feed to the

currently selected P16 output. Choices include:

• O

• Main L

• Main R

• Main C/M

• Any of the 16 Mix Outputs

• Any of the six Matrix Outputs

• Any of the 32 Direct Outputs

• Any of the eight Auxiliary Outputs

• Any of the FX Direct Outputs

• Monitor L

• Monitor R

• Talkback.

4. Tap the fourth encoder to assign the selected output path,

completingtheprocess.

5. Adjust the fth encoder to select the signal tap point for the output

assignment. This determines where in the audio signal path the source

is ‘tapped’ as it is sent to the P16 output. The available signal tap

pointsinclude:

• IN/LC

• IN/LC +M

• PreEQ

• PreEQ +M

• PostEQ

• PostEQ +M

• PreFdr

• PreFdr +M

• Post Fader.

6. Tap the fth encoder to complete the signal tap point assignment.

card out

The ROUTING screen’s card out tab allows the user to patch various signal paths

to the physical inputs and outputs on the DN32-USB card. The card’s signal path

provides 32 channels of inputs and 32 channels of outputs. The 32 card inputs can

be used as alternative sources for the two input fader layers, switchable in banks

of eight.

To assign an output path to the option card, perform the following steps:

1. Adjust the rst push encoder to select an 8-channel signal path that will be

sent to the rst eight channels of the card. Choices include:

• Local 1-8 • AES50-B 25-32

• Local 9-16 • AES50-B 33-40

• Local 17-24 • AES50-B 41-48

• Local 25-32 • Card 1-8

• AES50-A 1-8 • Card 9-16

• AES50-A 9-16 • Card 17-24

• AES50-A 17-24 • Card 25-32

• AES50-A 25-32 • Out 1-8

• AES50-A 33-40 • Out 9-16

• AES50-A 41-48 • P16 1-8

• AES50-B 1-8 • P16 9-16

• AES50-B 9-16 • Aux 1-6/Mon.

• AES50-B 17-24

2. Tap the rst encoder to assign the selected output path,

completingtheprocess.

3. Repeat the process with encoders 2-4 to select output paths for the other

24channels or card outputs.

aes50-a / aes50-b

The ROUTING screens aes50-a and aes50-b tabs allow the user to patch

various console output paths to the outputs of the dual AES50 connectors. These

connectors can feed other AES50-equipped devices, such as a digital stage box or

standalone multi-track recorder.

The M32 contains two separate AES50 connectors, labelled A and B. These dual

connectors allow for an increased level of exibility in networking the console to

various AES50-based equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas M32 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info