Bedienungsanleitung Midea MCDD-Serie (Seite 18 von 25) (Englisch)

588092

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

NOTE

Install the drain joint of the outdoor unit

Fit the seal into the drain joint, then insert the drain joint into the

base pan hole of outdoor, rotate 90° to securely assemble them.

Connect the drain joint with an extension drain hose (Locally

purchased), in case of the condensate draining off the outdoor

unit during the heating mode.

Seal

The base pan hole

of outdoor unit

Drain joint

Seal

The base pan

of outdoor unit

Drain

joint

Fig.9-1

All the pictures in this manual are for explanation

purpose only. They may be slightly different from the

air conditioner you purchased(depend on model).The

actual shape shall prevail.

The temperature of refrigerant circuit will be high, please

keep the interconnection cable away from the copper tube.

Dissemble the bolts from the cover.(If there isn't a cover on

the outdoor unit, disassemble the bolts from the maintenance

board, and pull it in the direction of the arrow to remove the

protection board.)

(Refer to Fig.10-1a、Fig.10-1b、Fig.10-1c)

Connect the connective cables to the terminals as identified

with their respective mached numbers on the terminal block

of indoor and outdoor units.

Re-install the cover or the protection board.

Connect the cable

10.1

The power connection for the air conditioner has to be

done at the main power distribution. The distribution has

to be of a low impedance, normally the required

impedance reaches at a 32 A fusing point.

No other equipment has to be connected with this power

line.

For detailed installation acceptance please refer to your

power supplier, if restrictions do apply for products like

washing machines, air conditioners or electrical ovens.

For power details of the air conditioner refer to the rating

plate of the product.

For any question contact your local dealer.

10. WIRING

The appliance shall be installed in accordance with

national wiring regulations.

The air conditioner should use separate power supply

with rated voltage.

The external power supply to the air conditioner should

have ground wiring, which is linked to the ground wiring

of the indoor and outdoor unit.

The wiring work should be done by qualified persons

according to circuit drawing.

An all-pole disconnection device which has at least 3mm

sepaaration distance in all pole and a residual current

device (RCD) with the rating of above 10mA shall be

incorporated in the fixed wiring according to the national

rule.

Be sure to locate the power wiring and the signal wring

well to avoid cross-disturbance.

Do not turn on the power until you have checked

carefully after wiring.

The power cord type designation is H07RN-F.

Remark per EMC Directive 2004/108/EC

For to prevent flicker impressions during the start of the

compressor (technical process) following installation

conditions do apply.

NOTE

Fig.10-1a

Protection board

Cover

installation manual

Fig.10-1b

Protection Board

Vertical discharge type outdoor unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea MCDD-Serie Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea MCDD-Serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info