Bedienungsanleitung Midea MCDD-Serie (Seite 19 von 25) (Englisch)

588092

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

NOTE

All the pictures in this manual are for explanation

purpose only. They may be slightly different from the

air conditioner you purchased(depend on model).The

actual shape shall prevail.

10.4 Outdoor unit

Wrong wiring connections may cause some electrical parts to

malfunction.

CAUTION

Remove the electric parts cover from the outdoor unit.

Connect the connective cables to the terminals as identified

with their respective matched numbers on the terminal block

of indoor and outdoor units. (Connective cable sheath

length to be removed and insert into the terminal block.)

To prevent the ingress off water, from a loop of the

connective cable as illustrated in the installation diagram of

indoor and outdoor units.

Insulate unused cords (conductors) with PVC-tape. Process

them so they do not touch any electrical or metal parts.

Fig.10-2

Cord wire

40mm10mm

The Specification of Power

10.2

Wiring figure

10.3

(Refer to Table10-1~Table10-8)

(Refer to Fig.10-3 Fig.10-10)

11. TEST OPERATION

The test operation must be carried out after the entire

installation has been completed.

Please confirm the following points before the test operation:

According to the user's requirement, install the remote

controller frame where the remote controller's signal can

reach the indoor unit smoothly.

Test operation

The indoor unit and outdoor unit are installed properly.

Tubing and wiring are correctly completed.

The refrigerant pipe system is leakage-checked.

The drainage is unimpeded.

The heating insulation works well.

The ground wiring is connected correctly.

The length of the tubing and the added stow capacity of

the refrigerant have been recorded.

The power voltage fits the rated voltage of the air

conditioner.

There is no obstacle at the outlet and inlet of the outdoor

and indoor units.

The gas-side and liquid-side stop valves are both opened.

The air conditioner is pre-heated by turning on the power.

Set the air conditioner under the mode of "COOLING" with the

remote controller, and check the following points. If there is

any malfunction, please resolve it according to the chapter

"Troubleshooting" in the "Owner's Manual".

1) The indoor unit

a. Whether the switch on the remote controller works well.

b. Whether the buttons on the remote controller works

well.

c. Whether the air flow louver moves normally.

d. Whether the room temperature is adjusted well.

e. Whether the indicator lights normally.

f. Whether the temporary buttons works well.

g. Whether the drainage is normal.

h. Whether there is vibration or abnormal noise during

operation

2) The outdoor unit

a. Whether there is vibration or abnormal noise during

operation.

b. Whether the generated wind, noise, or condensed of by

the air conditioner have influenced your neighborhood.

c. Whether any of the refrigerant is leaked.

I. Whether the air conditioner heats well in the case of the

HEATING/COOLING type.

installation manual

Fig.10-1c

Protection Board

Centrifugal fan outdoor unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea MCDD-Serie Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea MCDD-Serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info