Bedienungsanleitung Midland BTX1 (Seite 21 von 111) (Holländisch, Portugiesisch, Finnisch)

494048

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

20 - Midland BTX1

4. Enable the Bluetooth device search feature on your GPS

5. After some seconds, “Midland BTX1” will be displayed on your GPS.

6. Follow the pairing procedure of your GPS. If a pin code is requested you must

enter “0000” (four times zero).

7. When successfully paired, the Blue light of the unit will be on for one second

and then the unit will exit the setup mode and switch to the working mode

(the Blue light will start ﬂashing).

When you pair the GPS to the Volume + button, you loose the possibility to pair

the phone to the BTX1 unit. You can overcome this limit by pairing the phone

directly to the GPS and then the GPS to the BTX1 unit. All the phone features are

therefore managed by the GPS itself.

GPS navigator always in background

To keep the intercom open while the GPS give the street indication you must have

the “background” feature active.

How to pair PMR446 transceiver with integrated Bluetooth

If your PMR446 trasceiver has an integrated Bluetooth (like the G8BT), you must

pair the trasceiver using the “Volume +“ button:

› Turn oﬀ the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Now press ﬁrmly (3 sec) the “Volume +” button, the Blue and Red light will

ﬂash.

› Follow now the pairing procedure explained on the manual of the transceiver

itself

Attention: If you are pairing to a G8BT transceiver, just when the BTX1 ﬁnish the

pairing (only the Blu LED is ﬂashing) you must follow this procedure to activate the

Bluetooth connection:

› Shortly press to the “forward” button in “Phone” mode, a purple light will con-

ﬁrm the audio connection ON. Now it’s ready to transmitt and receive trough

the BTX1

› Follow the same procedure every time you need to reconnect the G8BT to the

BTX1 (no need to make the pairing procedure again)

Attention: the PMR446 audio connection can be set on “Stand by” pushing the

“forward” button on the BTX1 in “Phone” Mode

Attention: the connection with the Bluetooth radio (G8E-BT) can be set in “Stand

by” mode simply by pushing the “forward” button on the BTX1 in “Phone” Mode.

How to use the wired audio input

Your Midland BTX1 is also supplied with a wired audio input (AUX), that can

be used to connect an audio source, like an iPod (or any other MP3 Player) or a

PMR446 transceiver for group communication or for a coverage increase.

Listening to music

To listen to music from the wired input, connect the audio source using the op-

tional AUX cable.

The volume buttons (Vol + and Vol -) cannot be used to adjust the volume of the

wired audio source. The AGC system with automatically increase the volume on

higher speed.

Attention: never set the volume of the MP3 Player to the maximum possible. Nor-

mally the best level is about the 70% of the maximum.

Hint: We recommend that you perform a few tests adjusting the volume of your

iPod/MP3 player so at the normal speed the Headset volume is suited to your

needs. The AGC system will automatically increase the volume on higher speed.

Make a note to remember this setting for future trips.

Enabling/disabling the wired input

If needed the wired input can be enabled or disabled:

Enabling/Disabling: Make a Long press on the “Rear” button (you will hear one

audio beep tone for enabling conﬁrmation and two audio beep tone for disa-

bling).

Using a PMR446 transceiver with the cable connection

In order to connect the transceiver to your Midland BTX1, you need to purchase

the speciﬁc 2.5mm plug AUX cable, sold separately. S

ome manufacturers radios use a diﬀerent pin conﬁguration, so we recommend

that you ask your dealer as to which cable is best suited to your needs

The cable connected to the transceiver normally has also a PTT button that can

be placed on the handlebar of your bike or held in your hand (If you are the pas-

sanger rider).

To communicate via the attached radio, press the PTT button to speak and release

it to listen. It is not possible to talk and listen simultaneously.

Adjust the volume of the transceiver to your needs, remembering that the volume

adjustment is controlled by the automatic AGC system and that it will therefore

be automatically increased in relation to background noise.

If you wish to use a PMR446 transceiver for group communications and simulta-

neously maintain the Intercom feature enabled between two or more BTX1 devi-

ces, you must remember that every time you talk to communicate with the PMR

446 transceiver (pressing the PTT button), you will also activate the intercom of

the BTX1 to the unit connected to the “Middle” button (thanks to the VOX feature).

To avoid the Intercom activation when you speak on the PMR446, you can decide

to pair the BTX1 unit on the “Rear” or “Forward” (where the VOX is not active) or

if you still want to use the “Middle” button, you must disable the VOX feature, as

explained in the previous section.

Attention! If you disable the VOX feature, you will only be able to answer incoming

phone calls by pressing the “Forward” button.

Midland BTX1 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland BTX1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info