Bedienungsanleitung Midland BTX1 (Seite 22 von 111) (Holländisch, Portugiesisch, Finnisch)

494048

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

Midland BTX1 - 21

Setup and special conﬁgurations

Resetting all paired devices

Sometimes you may ﬁnd it necessary to delete all the pairing references stored in

the BTX1 unit (reset operation).

To perform this operation you must ﬁrst enter the setup mode:

› Turn oﬀ the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Than simultaneously press and hold down the “Volume +” and “Volume –“

buttons for 3 seconds. The Blue Light will be lit on for 1 sec and than back

to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the BTX1.

This procedure deletes all the paired Bluetooth devices stored in the memory and

it is therefore possible to start a new “clean” pairing session.

Back to factory setting

Sometimes you may ﬁnd it necessary to go back to the factory setting, to reset all

the changes/setup already made and have a “clean” unit.

To perform this operation you must ﬁrst enter the setup mode:

› Turn oﬀ the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Than simultaneously press and hold down all the three buttons “Forward”-

“Middle”-“Rear” for 3 seconds. The Blue Light will be lit on for 1 sec and than

back to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the BTX1.

Adjusting/ Disabling the VOX feature (Intercom and telephone)

The Intercom feature can be enabled both manually and vocally (VOX). The VOX

activation is inﬂuenced by the background noise and therefore by the speed.

For optimum results, it is possible to choose one of the following four microphone

sensitivity levels: high, medium, low and very low. The default setting of BTX1 is

“low”. It is also possible to disable the VOX feature in order to activate the Inter-

com and phone call answering features in manual mode only.

Adjusting the sensitivity of the microphone (VOX)

To perform this operation you must ﬁrst enter the setup mode:

1. Turn oﬀ the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

3. Your BTX1 is now in “Set up mode”.

4. Press the “Rear” button until the red light indicator changes to a steady blue.

5. Now, press “Volume +” or “Volume -“ to increase or reduce sensitivity. Every

time you press the Volume buttons the RED light will ﬂash for conﬁrmation.

When you reach the end of the upper and lower limit, the RED light will not

ﬂash.

6. Press again the “Backward” button; the Blue light will ﬂash several times, in

order to let you know the selected sensitivity:

One ﬂash = VOX disabled

Twice = very low sensitivity

3 times= low sensitivity

4 times= medium sensitivity (default setting)

5 times = high sensitivity

The light indicator is now back to steady RED (“Set up mode”) and the

changes are conﬁrmed

7. If needed, you can adjust again the sensitivity repeating the steps from point

1, otherwise exit the Setting mode by double clicking the “Middle” button.

Once the red light turns oﬀ, the blue led starts blinking. Now you can use your

BTX1.

Disabling the VOX feature (Intercom and telephone)

Follow all the procedure described in the previous steps and choose the option of

only one ﬂash (VOX disabled).

Wired connection always in background

This feature let you keep the wired connection always on, even when the phone

or the intercom is open. This feature can be useful when you connect a PMR446

transceiver.

By default this option is on.

Disabling:

› Enter the “Setup” mode:

› Turn oﬀ the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Press the “Forward” and “Middle” button together for 3 seconds. The blue LED

will ﬂash twice.

› Double click on the “Middle” button to exit the “Setup” mode and use the BTX1.

Enabling:

Follow the same procedure up described; now the blue LED will ﬂash once.

To exit the “Setup” mode, double click the “Middle” button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BTX1 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland BTX1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info