Bedienungsanleitung Midland BTX2 FM (Seite 17 von 88) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

579660

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

16 - Midland BTX2 FM

Wired microphone

Using the Velcro/adhesive strip, place the microphone inside the helmet in front

of your mouth. This type of microphone is more suited for Full Faced helmets. The

mini connector on the microphone allows you choose the microphone that best

suits the helmet you are using.

Audio kit jack

The audio kit must then be connected to the central jack of the Midland BTX2 FM

unit using the “L” shaped connector.

Description of the installation brackets

The Midland BTX2 FM can be ﬁxed onto the helmet in two diﬀerent ways: By ei-

ther using the plate with bi-adhesive strip, or the clamp. These methods allow you

to safely “ﬁx” the BTX2 FM unit onto your helmet and to remove it at any time in

order to recharge or store it.

Plate with bi-adhesive strip

The ﬁxing plate has a bi-adhesive strip on one of

its sides. To ﬁx the plate in place, clean the appli-

cation area on the helmet surface, remove the bi-

adhesive ﬁlm and

place the ﬁxing plate on the helmet by keeping it

contact with the surface for a few seconds.

Screw Clamp

Using the Allen Key, loosen the two screws on the clamp and place the rear plate

between the helmet padding and the external rigid protection. Then, tighten the

two screws in order to ﬁrmly ﬁx the clamp in place. Inside the clamp is included a

small plastic spacer that can be removed to give a tighter ﬁt if required.

Fitting and removing your Midland BTX2 FM

The BTX2 FM can be easily ﬁtted onto the helmet by sliding it downwards so that

it ﬁts into the slot of the selected ﬁxing device (plate with bi-adhesive strip or

clamp). BTX2 FM is maintained in position thanks to the ﬁxing clip located on

the upper section (A).

To detach the BTX2 FM, simply press the ﬁxing clip and push the unit upwards.

Switching your Midland BTX2 FM on and oﬀ

Switching the unit on:

Press and hold “Middle” button down for approximately 3 seconds until the BLUE

indicator lights.

Switching the unit oﬀ:

Press and hold both “Middle” and “Backward” buttons together for approximately

3 seconds until the RED indicator ﬂashes 3 times, thus lessening the chances that

you might turn oﬀ the unit accidentally (especially whilst wearing gloves).

Operative “mode”

The BTX2 FM can operate in three main “mode”: Intercom, Phone and FM Radio.

The 3 multi function buttons can have diﬀerent functionality depending on which

mode the unit is at that moment.

› In “Intercom mode” the middle buttons let you manage the communications

between driver and passanger

› In “Phone mode” you can manage your Bluetooth cellular phone to place/

answer a phone call or to listen to the music (in stereo mode). Please use your

phone responsibly and safely.

› In “FM Radio mode” you can listen to your favourite radio station in stereo,

seek for a speciﬁc radio station and save it (6 memory are available).

You can switch (toggle) from one mode to the other simply pressing the Middle

button for 3 seconds. A voice announcement will tell in which mode you are on.

The toggle sequence is the following:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BTX2 FM Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info