Bedienungsanleitung Midland BTX2 FM (Seite 18 von 88) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

579660

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Midland BTX2 FM - 17

› Intercom mode (if another unit has been paired)

› FM Radio

› Phone mode (if a phone has been paired)

Every time you turn on the unit, the default mode is Intercom (if it was previously

paired to another unit), otherwise it will be Phone (If was paired to a phone).

If you need to know in which mode the unit currently is, just press the “Volume +

“ and “Volume –“ button together. A voice announcement will tell you the current

mode.

Maximum Distance

You can reach 800mt intercom distance if the ﬂip up antenna is up and if you are

in line of site without obstructions and interferences (the riders must be always

in sight).

How to pair two BTX2 FM unit

The two units supplied in the same BTX2 FM box, are already paired and ready to

use, which mean you don’t need to perform this procedure. The unit are already

paired using the Middle button.

If the devices are not part of the same kit, or the units has been purchased sepa-

rately, you need to ﬁrst pair it in order to use it.

To pair the BTX2 FM to another BTX2 FM unit

To pair the BTX2 FM to another BTX2 FM unit, you must ﬁrst enter the setup mode:

1. Turn oﬀ the unit

2. Press and hold down the middle button about 7 sec., until the Red light is on

permanently.

3. Now press the Middle button for 3 seconds. The Blue and Red light will ﬂash.

4. Do the same procedure on the other unit, When successfully paired, each unit

will have the Blue light on for one second and than go back to the setup mode

(Red light always on).

5. Now the pairing procedure is complete, you just need to exit the setup mode

before you can use the units:

6. Double click on the Middle button, the Red light will turn oﬀ and the Blue

light will start ﬂashing.

You can use now your BTX2 FM.

How to use the Intercom

To use the intercom feature, be sure the both units are turned on and correctly

paired together.

Manual activation

Press the Middle button on one of the two units. Communication is enabled and

remains active until you press again the middle button. The intercom need some

second to activate, you will hear a beep tone when the intercom is open.

Voice activation (VOX)

Simply start talking, after some seconds the communication will be opened and

will remain active for the time you are talking. If there is no conversation the

intercom will be closed after 40 seconds. If needed you can close the intercom

manually without waiting 40 seconds (just press the middle button).

Attention: The Voice activation (VOX) can open the intercom communication only

to the unit that was paired with the Middle button. If you chose to use a diﬀerent

button, you will be able to active the intercom only manually.

If needed, you can disable the VOX feature simply by pressing the Backward but-

ton for 7 sec. A voice announcement will advise you when the VOX is disabled.

To turn the VOX on again, just press the same button and a voice announcement

will advise you that the VOX is now active. This setting is remembered also if you

turn oﬀ the unit

Adjusting the volume

Your Midland BTX2 FM uses AGC technology, which automatically adjusts the

listening volume in relation to background noises.

However, it is also possible to manually adjust the volume by means of the “Volu-

me +” and “Volume -“buttons.

Attention: volume can be adjust only when an audio connection is active.

Attention: the volume buttons (Vol + and Vol -) cannot be used to adjust the vo-

lume of the wired audio source. The AGC system with automatically increase the

volume on higher speed.

Compatibility with other Midland BT line units

The BTX2 FM is compatible with BT Next Conference and BTX1 FM.

When paired the max distance of the intercom is deﬁned from the lower possible.

The BTX2 FM is compatible with the previous line of Midland BT (BT Next, BTX2

and BTX1) only if updated to ﬁrmware version 2014.

How to pair BTX2 FM to more than 2 units

One BTX2 FM unit can be paired to maximum three other BT unit, that means

4 in total (three Midland unit + one Talk2All). You can use the Middle and the

Backward button to pair to a Midland unit and you can use the “Forward” button

to pair the “Talk2All-Universal Intercom” feature.

The same button you will use to pair the unit will be also used to open/close the

intercom communication.

For example you can pair your passenger to the Middle button and another mo-

torbiker to the Backward button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BTX2 FM Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info