Bedienungsanleitung Midland BTX2 PRO 2020 (Seite 16 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

738681

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

12 www.midlandeurope.com www.midlandeurope.com 13

3. Now press ﬁrmly (3 sec) the “Volume +” or “Volume -” button, the Blue and Red

lights will ﬂash.

4. Enable the Bluetooth device search feature on your GPS

5. After some seconds, “Midland BTX2 PRO” will be displayed on your GPS.

6. Follow the pairing procedure of your GPS. If a pin code is requested you must enter

“0000” (four times zero).

When successfully paired, the Blue light of the unit will be on for one second and then

the unit will exit the setup mode and switch to the working mode (the Blue light will

start ﬂashing). You can now use your Midland BTX2 PRO and the GPS street voice

announcement are always in background. If you pair the GPS to the Volume + button

(because for example the “Volume –“ button was already used), you lose the possibility

to pair the phone to the Midland BTX2 PRO unit. You can overcome this limit by pai-

ring the phone directly to the GPS and then the GPS to the Midland BTX2 PRO unit.

All the phone features are therefore managed by the GPS itself.

Pairing to a PMR446 radio with integrated or external Bluetooth

The PMR446 Radio can be paired to the “Volume +“ or “Volume -” button. If paired

on “Volume -” and the “Background” feature is activated, the PMR446 radio is always

in the background even when you talk on the intercom.

Pairing procedure

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is on per-

manently.

› Now press ﬁrmly (3 sec) the “Vol +” or “Vol -” button, the Blue and Red light will

ﬂash.

› Follow now the pairing procedure explained on the manual of the transceiver itself.

How to listen to the FM Radio

The FM Radio receiver is integrated inside the unit. You just need to switch to the “FM

Radio” mode in order to use it. Long press the middle button until you hear “FM radio”

from the voice announcement. Now all the three main buttons are dedicated to the

FM Radio (See Table C).

Press short the Forward or the Backward button to seek the FM Radio station.

When you press long the Forward or the Backward button, you can scan up or down

the 6 recorded stations. A voice announcement will tell you the number of which me-

mory you are entering. To save the station you are listening to, press the Forward and

Backward buttons together for 3 sec. You will hear a beep tone for conﬁrmation.

The station is saved over the last recorded station used.

Thanks to the RDS system, the FM Radio will choose the strongest signal available for

the radio station you like to listen. The RDS system is OFF by default, if needed you

can toggle on/o the RDS pressing together the “Volume +” and “Volume –“ buttons

for 3 sec when the radio is on. A voice announcement will tell you the RDS status.

How to Disable/Enable the FM Radio

By default the FM radio is on.

Disabling:

› Enter the “Setup” mode: turn o the unit and hold down the “Middle” button about

7 sec., until the Red light is on permanently.

› Press “Middle” and “Volume+” buttons together for 3 seconds. The blue LED will

ﬂash three times.

› Double click on the “Middle” button to exit the “Setup” mode and use the Midland

BTX2 PRO

Enabling:

› Follow the same procedure up described; now the blue LED will ﬂash once.

To exit the “Setup” mode, double click the “Middle” button.

FM Radio with intercom

When you are in “FM Radio” mode is not possible to manually open the intercom, you

can only open it using VOX feature (just talk) to the unit paired on the “Middle” button.

To manually activate the intercom you must switch to “Intercom” mode.

Setup and special conﬁgurations

Resetting all paired devices

Sometimes you may ﬁnd it necessary to delete all the pairing references stored in the

Midland BTX2 PRO unit (reset operation).

To perform this operation you must ﬁrst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button 7 sec., until the Red light is on perma-

nently.

› Then simultaneously press and hold down the “Volume +” and “Volume –“ buttons

for 3 seconds. The Blue Light will be lit on for 1 sec and than back to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode.

This procedure deletes all the paired Bluetooth devices stored in the memory and it is

therefore possible to start a new “clean” pairing session.

Back to factory setting

Sometimes you may ﬁnd it necessary to go back to the factory setting, to reset all the

changes/setup already made and have a “clean” unit.

To perform this operation you must ﬁrst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is on per-

manently.

› Then simultaneously press and hold down all the three buttons “Forward”-“Midd-

le”-“Backward” for 3 seconds. The Blue Light will be lit on for 1 sec and than back

to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the Midland

BTX2 PRO

Adjusting/ Disabling the VOX feature (Intercom and telephone)

The Intercom feature can be enabled both manually and vocally (VOX). The VOX acti-

vation is inﬂuenced by the helmet type, the background noise and therefore by the

speed.

For optimum results, it is possible to choose one of the following four microphone

sensitivity levels: high, medium, low and very low. The default setting of Midland BTX2

PRO is “High”. It is also possible to disable the VOX feature in order to activate the

Intercom and phone call answering features in manual mode only.

Adjusting the sensitivity of the (VOX)

To perform this operation you must ﬁrst enter the setup mode:

1. Turn o the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is on per-

manently.

3. Your Midland BTX2 PRO is now in “Set up mode”.

4. Press the “Backward” button shortly and the red light changes to a steady

blue.

5. Now, press “Volume +” or “Volume -“ to increase or reduce sensitivity. Every time

you press the Volume buttons the RED light will ﬂash for conﬁrmation. When you

reach the end of the upper and lower limit, the RED light will not ﬂash.

6. Press again the “Backward” button shortly; the Blue light will ﬂash several times, in

order to let you know the selected sensitivity:

One ﬂash = VOX disabled

Twice = low sensitivity

3 times= normal sensitivity

4 times= high sensitivity (default setting)

5 times = Highest sensitivity

The light indicator is now back to steady RED (“Set up mode”) and the changes

are conﬁrmed

7. If needed, you can adjust again the sensitivity repeating the steps from point 1,

otherwise exit the Setting mode by double clicking the “Middle” button. Once the

red light turns o, the blue led starts blinking. Now you can use your Midland BTX2

PRO

C-Radio FM mode

Mode Forward button Middle button Rear button

FM Radio Short press: seek station up

Long press: Scan recorded Short press: On/o

Long press: Change mode Short press: seek station up

Long press: Scan recorded

Midland BTX2 PRO 2020 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info