Bedienungsanleitung Midland BTX2 PRO S (Seite 26 von 124) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

738621

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

24 www.midlandeurope.com

previous connection will be closed. The connection is not a “chain”, when two

persons are talking it is not possible to break (interrupt) the communication by

one of the other two units.

Pair the Midland BTX2 PRO S to another Midland BTX2 PRO S unit

To pair the Midland BTX2 PRO S to another Midland BTX2 PRO S unit, you

must ﬁrst enter the setup mode:

1. Turn o the unit

2. Press and hold down the middle button about 7 sec., until the Red light is

on permanently.

3. Now press one of the three buttons (Forward, Middle or Backward) for 3

seconds depending on which button you would like use to open the inter-

com to the other unit. The Blue and Red lights will ﬂash.

4. Repeat the same procedure on the other unit, you don’t need to use the

same button, you can choose one of the three buttons not previously used.

5. When successfully paired, each unit will have the Blue light on for one se-

cond and then go back to the setup mode (Red light always on).

6. Now the unit is ready for another pairing procedure, and you can pair

another Midland BTX2 PRO S unit following the same procedure, but using

a dierent button.

If you don’t have more devices to pair, you must exit the setup mode before

you can use the units:

› Double click on the Middle button, the Red light will turn o and the Blue

light will start ﬂashing. You can use now your Midland BTX2 PRO S

How to use the Intercom with more than two units

To use the intercom feature, be sure that all the units are turned on and cor-

rectly paired together.

Manual activation in Intercom mode

When in “Intercom Mode” press the button corresponding to the unit you

would like to communicate with. After some seconds the intercom commu-

nication will open. The communication remains active until you press again

the same button. To quickly open the intercom to another person, just press

the button corresponding to the other unit, the intercom will be automatically

closed and the new connection will be open (see Table A).

Voice activation (VOX)

The voice activation feature can open the intercom only to the unit paired to

the Middle button.

Hint: this feature is very useful when you have a speciﬁc person that you like to

talk to more often (for example your passenger). In this way you don’t need to

press a button to open the communication.

Unit already busy in a conversation

If you try to open an intercom connection to another person that is already

talking with someone else (or is in a middle of a phone conversation), you will

hear a “busy” double beep tone. Just wait sometime and try again, maybe this

time the “line” is not busy.

The person who is called, will be advised that someone is trying to call and will

hear a voice announcement with the number of the button from which the

A- Manual activation

Mode Forward button Middle button Rear button

Intercom Short press: Open/Close intercom to paired

raider

Short press: Open/Close intercom to paired

raider

Long press: Change mode

Short press: Open/Close intercom to paired

raider

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BTX2 PRO S Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland BTX2 PRO S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info