Bedienungsanleitung Mobius ActionCam (Seite 8 von 15) (Englisch)

583594

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

In-Camera Formatting

The Camera contains a built-in formatter which may be used to format the SD card. In-

Camera formatting is best done using mSetup.exe (see below) but can also be done as

follows:

•

Connect the camera to an External USB power supply or to a PC as a Removable

disk (see above).

•

Press and hold down the Mode button. DO NOT RELEASE the button until after

the next steps are completed.

•

Disconnect the camera from the power supply or the computer.

•

The yellow LED will blink for a few seconds followed by three blinks of the red LED,

after which the camera will turn off. You must wait until you see the red LED blink

three times.

•

Release the Mode button.

►In firmware versions up to v2.03 cards with a capacity greater than 32GB will be

formatted with exFAT. All other cards will be formatted as FAT32. See the note about using

exFAT in older operating systems in the Description.

Camera Setup (Configuration)

On Windows it is recommended to always use the program mSetup.exe to modify the

camera's configuration. mSetup communicates directly with the camera and makes

configuring the camera a very simple task.

It is, however, also possible to manually change the configuration settings by editing the

"SYSCFG.TXT" file which must be placed in the root folder of the card for the camera to

find and load the new settings. You can use any ASCII editor, for example Notepad, to

modify the parameters. The "SYSCFG.TXT" must be in plain ASCII, it must not be in

Unicode. If you don't know what a root folder is, or you don't know what ASCII is or don't

know how to manually edit ASCII files please only use mSetup.exe.

A "SYSCFG.TXT" file must first be generated by the Camera. The camera's parameters are

self explanatory. It is important not to change the sequence of the square brackets and not

configure invalid combinations. For example, never combine a clip longer than 5 minutes

with the continuous loop. If you enter invalid combinations or values, the Camera will not

perform as expected. It is much safer to use the setup program which will always configure

the camera correctly. If you want to keep the camera's current date and time, replace all the

numeric characters withing the square brackets by ?.

The "SYSCFG.TXT" file can be automatically generated as follows:

1. Disconnect the camera from the PC and turn it off.

2. Press and Hold Down the Mode button. DO NOT RELEASE the button until

step 4.

3. Press and Hold Down the Power button until the RED LED blinks 3 times and the

camera turns off. This will take about 5 seconds. During the process, the blue and

yellow LEDs may blink.

4. Release the Mode and Power buttons.

The SYSCFG.TXT file showing the camera's current settings should now be in the memory

card root folder. Now you can edit the SYSCFG.TXT file as indicated above, and load the

new settings back into the camera by using exactly the same method as outlined in steps 1

through 4, above. Once completed, the "SYSCFG.TXT" file will be automatically deleted

from the card's root folder.

►Some parameter settings are not allowed in combination with other parameter settings.

For example, only clip lengths of 5 minutes and less are allowed when loop recording is

enabled. The Windows configuration setup program mSetup.exe (see below) guarantees

the settings are valid. Use the tool tips to show you which parameter combinations are

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mobius ActionCam Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info