Bedienungsanleitung Monacor DMR524 (Seite 12 von 60) (Englisch)

632632

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

BASIC OPERATION

-8-

3. CONNECTIONS AND SETUP

3.1 Install HDD

The HDDs must be installed before the DVR is turned on. For detailed installation instructions, please refer to

section "APPENDIX 1 INSTALL HDD" at page 50.

3.2 Camera Connection

The cameras must be connected and power-supplied before the DVR is turned on. For detailed DVR video input /

output ports, please refer to section “2.2 Rear Panels” at page 6. For detailed external I/O port description, please refer to

section “APPENDIX 2 PIN CONFIGURATION” at page 51. For detailed camera setup, please refer to its own manual.

Note: When using LOOP function, set the impedance switch at your DVR rear panel to HI-IMPEDANCE to

decrease interferences. The default setting is 75Ω.

3.2.1 Normal Camera Connection

1) Connect the camera with indicated power supply.

2) Connect the camera video output to the DVR video input port with a coaxial cable and BNC connector.

For detailed camera title, ID, protocol and baud rate setup, please refer to section “6.4.5 Remote” at page 22.

3.2.2 PTZ Camera Connection

1) Connect the PTZ camera with indicated power supply.

2) Connect the PTZ camera video output to the DVR video input port with a coaxial cable and BNC connector.

3) For using DVR to control the PTZ camera, please connect the RS485-A line (brown) of the PTZ camera to the PIN11 of

the DVR DSUB solder side, and connect RS485-B line (orange) to the PIN10 of the DVR DSUB solder side.

And then solder them together in case of loosening.

Note: For detailed camera ID, protocol and baud rate setup at DVR side, please refer to section “6.4.5

Remote” at page 22. For detailed camera ID, protocol and baud rate setup at remote AP software side,

please refer to section “(1) Device” at page 39 (AP software system configuration). For detailed PTZ

control instructions, please refer to section “6.6.5 PTZ Camera Setup and Control” at page “30”.

3.3 External Device Connections

3.3.1 VGA Converter (Optional)

This optional peripheral (VGA Converter) allows your DVR to have VGA output function. Connect VGA CONNECTER

(A) to the MONITOR VGA CONNECTER (a), and connect VGA CONNECTER (B) to the DVR D/V PORT (b).

Please refer to the following figure as an example.

3.3.2 IR Transmitter

For MODEL 4 & MODEL 5 DVR, IR remote control is supported (Other models are optional). Please connect the IR

receiver line to the IR port on the DVR rear panel. And make sure the IR function is activated in the DVR menu (The

default setting is on). Please refer to the following figure as an example.

D / V

A: Connect to MonitorVideo Input

B: Connect to DVRVideo Output

MONITOR

VGA

USB

INP UT

DC 1 9V

VD/

LOOP

EXT ERNAL I/OIR

INP UT

LOOP LOOP LOOP

INP UT

LAN

ACT.

LINK

CALLMONITOR

IN OUT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Monacor DMR524 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Monacor DMR524

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info