Bedienungsanleitung Monacor DMR524 (Seite 14 von 60) (Englisch)

632632

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

BASIC OPERATION

-10-

3.6.2 DDNS Apply

You need to apply a DDNS account before setting PPPoE or DHCP connection. DDNS is a service for transforming

the dynamic IP corresponding to a specific “Hostname”. For DDNS setup, please refer to the steps below.

‧ Go to a website which provides free DDNS services and apply a “Hostname”.

For example, go to http://www.dyndns.com.

‧ Enter all the information necessary for signing up an account according to the website instructions.

‧ Then, you will see the screen “Account Created”, and Dyndns will email the instructions to your specified E-mail

address for enabling your account. You must complete the procedure according to the instructions in the mail. That is

to must visit the confirmation address within 48 hours of the time that the e-mail was sent to complete the account

creation process. Then, you will see “Account Confirmed”. Your account is created successfully now.

‧ Log in with your account information and click ”My Service”.

‧ Click ”Add Host Services”.

‧ Click ”Add Dynamic DNS Host”.

‧ Fill in and choose the desired host name.

‧ The host name is created. You will be connected to the corresponding IP address whenever you enter this hostname.

3.6.3 Dynamic IP － PPPOE

1) Build a Local Area Network (LAN) between DVR and PC/NB with network cable:

Your NB/PC and DVR must be under the same network domain to build the area network. Please change the IP

address of your PC/NB into 192.168.1.X (X can be the number between 1~255, except 10) and the subnet mask into

255.255.255.0 for communicate with the DVR.

Install the supplied AP software on your NB/PC. And then login the DVR with the supplied AP software for the

following default DVR settings.

‧ The DVR default IP address: 192.168.1.10

‧ The DVR default account / password: admin

‧ The DVR default port: 80

2) Set DVR network setting in “SYSTEM CONFIG” → “Network” of the supplied AP:

In the “SYSTEM CONFIG” → “Network” of the supplied AP, select the “PPPOE” in “IP TYPE” section. And then

type the “User Name” and “Password” obtained from your ISP. Press ”APPLY” button to confirm the setting.

3) Set DVR DDNS setting in the “SYSTEM CONFIG” → “DDNS” of the supplied AP software:

‧ DDNS: Choose “Enable”.

‧ User Name: Type your DDNS account.

‧ Password: Type your DDNS password.

‧ Domain: Type the “Host Name” you applied previously (EX: securityanytime.dyndns.org).

‧ System Name: Choose the DDNS server where you applied the domain name (EX: dyndns).

‧ After setting, please press “APPLY” button to confirm and finish the setting.

4) Login your DVR via an Ethernet or dial-up network.:

After setting up the network information of the DVR and connect it to the network, you can type DDNS host name,

default user name and password in the supplied AP software login page to log into your DVR remotely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Monacor DMR524 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Monacor DMR524

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info