Bedienungsanleitung Monacor DMR524 (Seite 13 von 60) (Englisch)

632632

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

BASIC OPERATION

-9-

3.4 DVR Power Setup

This device should be operated only with the type of power source indicated on the manufacturer’s label. Connect the

indicated AC power cord to the power adapter, and plug into an electrical outlet. “POWER” LED will be on as red. Press

“POWER” button, and “POWER” LED will be on as green. It takes approximately 10 to 15 seconds to boot the system.

3.5 Date and Time Setting

Before operating your DVR, please set the date and time on your DVR first.

You can use the following buttons for menu setting:

BUTTON FUNCTION

UP, DOWN, LEFT, RIGHT Move the cursor.

＋ , －

Choose numbers / selections.

ENTER Go to the submenu / confirm the selection.

MENU Go to the menu list / confirm the change / exit the menu list.

1) Date and System Time:

The menu path is as following: “MENU” → “DATE”.

2) Daylight Saving:

The menu path is as following: “MENU” → “DATE” → “DAYLIGHT SAVING”. Take the following option as an example:

DAYLIGHT SAVING

START 4

-SUN-MAR 24:00:00

END 4

-SUN-OCT 24:00:00

ADJUST 01:00

Note: Please DO NOT change the date or time of your DVR after the recording function is

activated. Otherwise, the recorded data will be disordered and you will not be able to find the

recorded file to backup by time search. If users change the date or time accidentally when the

recording function is activated, it’s recommended to clear all HDD data, and start recording again.

3.6 LAN or Internet Setup

3.6.1 STATIC IP

1) Build a Local Area Network (LAN) between DVR and PC/NB with network cable:

Your NB/PC and DVR must be under the same network domain to build the area network. Please change the IP

address of your PC/NB into 192.168.1.X (X can be the number between 1~255, except 10) and the subnet mask into

255.255.255.0 for communicate with the DVR.

Note: Before changing the network properties of your PC/NB, please write down the original network

properties in case you need to recover the properties later.

Install the supplied AP software on your NB/PC. Then, log into the DVR with the supplied AP software for the

following default DVR settings.

‧ The DVR default IP address: 192.168.1.10

‧ The DVR default account / password: admin

‧ The DVR default port: 80

2) Set DVR network setting in “SYSTEM CONFIG” → “Network” of the supplied AP:

In the “SYSTEM CONFIG” → “Network” of the supplied AP, select the “Static IP” in “IP TYPE” section. And then

type the “Server IP”, “Gateway”, “Net Mask” and “Web Port” (1~9999) information obtained from your ISP.

Press ”APPLY” button to confirm the setting.

3) Login your DVR via an Ethernet or dial-up network.:

After setting up the network information of the DVR and connect it to the network, you can use the IP address / Port

/ Account / Password you just entered in the supplied AP software to log into your DVR remotely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Monacor DMR524 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Monacor DMR524

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info