Bedienungsanleitung MTD CubCadet serie 6000 (Seite 15 von 25) (Englisch)

507839

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

English User manual

Stopping the engine

 Cool the engine down

appropriate to the previous

workload.

– In the case of less of a

workload.

Set the throttle to the

position and let the engine run

for approx. 1 minute.

– In the case of a high workload:

set the throttle to the middle

setting and let the engine run

for 3–5 minutes.

 Set the ignition key to /0.

 Remove the ignition key.

 Lock the parking brake.

Driving the tractor

t~êåáåÖ

^Äêìéí=í~âÉçÑÑI=ëíçééáåÖ=ëìÇÇÉåäóI=

~åÇ=ÇêáîáåÖ=~í=ÉñÅÉëëáîÉ=ëéÉÉÇë=

ê~áëÉ=íÜÉ=êáëâ=çÑ=~ÅÅáÇÉåíë=~åÇ=Å~å=

Å~ìëÉ=Ç~ã~ÖÉ=íç=íÜÉ=ìåáíK=_É=

ÉëéÉÅá~ääó=Å~ìíáçìë=ïÜÉå=êÉîÉêëáåÖK=

kÉîÉê=ÅÜ~åÖÉ=íÜÉ=ÇáêÉÅíáçå=çÑ=íê~îÉä=

çê=íÜÉ=ëéÉÉÇ=ïáíÜçìí=Ñáêëí=ÄêáåÖáåÖ=

íÜÉ=îÉÜáÅäÉ=íç=~=ëí~åÇK

kÉîÉê=ëÉíL~Çàìëí=íÜÉ=ÇêáîÉêÛë=ëÉ~í=

ïÜáäÉ=íÜÉ=ìåáí=áë=ãçîáåÖK

 Set the driver seat.

 Set the belt and put it on.

 Start the engine as stated.

 Raise the attachments which are

mounted to the 3 point

attachment device.

 Press the brake pedal down fully

and release the parking brakes.

 Set the drive lever to the desired

speed (high/low).

 Set the drive lever to the optimum

range for the job (as a rule,

maximum).

 Release the brake pedal and

slowly actuate the forwards/

backwards pedal until the desired

speed has been reached.

Before starting the journey, make

sure that the front wheels are in

the desired direction.

Note

The lower drive lever speed setting

should

– be used to travel on slopes and

uneven ground,

– when using attachments on the

PTO.

The forwards/backwards pedal

does not work if the parking brake is

locked.

Actuating when the parking brake

is locked leads to premature wear

and tear of the transmission

assembly.

Stopping/Parking the

tractor

 Release the accelerator and step on

the brake pedal until the vehicle

comes to a stand.

 Set the gear lever to the neutral

setting N.

 Switch off the PTO-switch.

 Stop the engine as stated.

 Lower mounted accessories

using the central hydraulics.

 Engage the parking brake and

remove the ignition key before

leaving the appliance.

Switching the differential

lock on and off

t~êåáåÖ=

oáëâ=çÑ=~å=~ÅÅáÇÉåí=çÅÅìêêáåÖ=~åÇ=

Ç~ã~ÖÉ=íç=íÜÉ=îÉÜáÅäÉK

Ó låäó=ëïáíÅÜ=íÜÉ=ÇáÑÑÉêÉåíá~ä=äçÅâ=çå=

ïÜÉå=íÜÉ=îÉÜáÅäÉ=áë=~í=~=ëí~åÇK

Ó aç=åçí=~Åíì~íÉ=íÜÉ=ÇáÑÑÉêÉåíá~ä=äçÅâ=

ïÜÉå=ÇêáîáåÖ=çå=íÜÉ=êç~Ç=

EÜ~êÇÉåÉÇ=ëìêÑ~ÅÉF=~åÇ=~í=ëéÉÉÇ=

EëíÉÉêáåÖ=ÇáÑÑáÅìäíáÉë=Ó=êáëâ=çÑ=~å=

~ÅÅáÇÉåíFK

Note

The vehicle is equipped with an

automatic four wheel drive which

additionally powers the fromt axles if

required.

 Bring the vehicle to a stand.

 Depress the differential lock fully

and keep it depressed.

The differential lock is activated

(even transfer of power onto both

rear wheels).

 Release differential lock pedal.

The differential lock is switched

off.

Note

Releasing the differential lock pedal

does not always disengage the

differential lock. You may have to

reduce the tractor’s speed or

reverse direction (first stop the

appliance) before you can

disengage the differential lock.

Four wheel drive

The four wheel drive automatically

switches the front axle drive on if the

transmission establishes that the

wheels have beeen turned and

additional traction is necessary.

For this, the user does not have to

do anything.

Using the 3 point

attachment device

t~êåáåÖ

_ÉÑçêÉ=ìëáåÖ=íÜÉ=P=éçáåí=~íí~ÅÜãÉåí=

ÇÉîáÅÉ=çê=EìåJFÜççâáåÖ=~ÅÉëëçêáÉëI=

~äï~óë=ëïáíÅÜ=íÜÉ=mql=~åÇ=íÜÉ=

ÉåÖáåÉ=çÑÑK=t~áí=ìåíáä=íÜÉ=íê~ÅíáîÉ=ìåáí=

áë=ÄêçìÖÜí=íç=~=ëí~åÇK

Setting the 3 point attachment

device

Fig. 17

 The adjustable lifting arm on the

right can be set in order to

position the lower transverse links

Loosen the counter nuts (a) and

turn the setting pipe (b) in order to

shorten or lengthen the lifting

coupling.

After setting, re tighten the

counter nuts on the setting pipe.

Fig. 18

 The length of the upper transverse

link is normally determined by the

shape of the acessory. In order to

set the upper transverse link,

loosen the locking lever (a) and

turn the setting pipe (b). Tilt the

locking lever back again if the

desired length is not reached. Set

correctly, the upper transverse link

lies parallel or almost parallel to the

lower transverse links.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 6000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info