Bedienungsanleitung MTD CubCadet serie 6000 (Seite 14 von 25) (Englisch)

507839

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

User manual English

Preparing for operation

 Park the tractor on an even, solid

surface.

 Lock the parking brake.

 Conduct all work with the engine

switched off.

 Remove the ignition key.

Set the driver seat

The driver's seat is adjustable in

terms of height, longitude and

hardness.

Setting the seat longitudinally

Fig. 14 a

 Take your place on the driver

seat.

 Pull the lever (1) outwards and

bring the seat into the desired

position.

 Release the lever and engage the

seat by gently moving it forwards

and backwards.

Adjusting the height

Fig. 14 a

 Setting the seat higher.

Turn the knob (2) in a clockwise

direction.

 Setting the seat lower.

Turn the knob (2) in a clockwise

direction.

Setting the driver seat hardness

Figure 14 b

 Swivel the lever (3) forwards such

that when turning, the lever does

not hit the seat.

 Setting the seat harder:

Turn the lever in a clockwise

direction.

 Setting the seat softer:

Turn the lever in an anti-clockwise

direction.

 Swivel the lever back.

Setting the seat belt

Fig. 15

Note

If the seat belt is too long or too short

to be set by pulling on the upper lying

belt, the position of the readjustment

clip should be changed. To do this,

hold the readjustment clip tightly and

pull the under lying belt through the

clip.

Move the clip towards the anchor

point of the seat to shorten the belt

or to make it longer.

Set the final length of the belt with the

readjustment clip, the latch and the

upper lying belt into the

right

half

of the belt.



In order to lengthen the belt, hold

the readjustment clip (a) ends tightly

and tip the side of the clip upwards

towards the latch.



While holding the clip, pull the

upper lying belt through clip

towards the latch (b).



Hold the belt and pull the latch to

the

left

in order to remove the slack

in the upper lying belt between the

readjustment and the latch.



To shorten the belt, tip the other

side of the clip upwards, pull the

free end of the belt to the

êáÖÜí

and

pull the latch to the

äÉÑí

in order to

remove the slack.

Filling and checking the oil

level

Note

The engine should already have

been filled with oil at the factory –

please check and where necessary,

top it up.

 Fill with ‘diesel’.

 Fill the fuel tank to a maximum of

2.5 cm below the lower edge of

the filler neck.

 Turn the fuel tank stopper tight.

 Check the oil level.

The oil level must lie between the

‘full/max’ and ‘add/min’ mark

(see also the engine manual).

Check the cooling water fill

level

Fig. 16

The cooling water fill level must be

located between the MIN and MAX

marker on the adjustment container.

Top up where necessary (see

section “Servicing”).

Check the tyre pressure

Note

For manufacturing reasons, the tyre

pressure can be higher than

necessary.

 Check the tyre pressure. Correct

where necessary (see section

“Servicing”).

–front 0.7 bar

– rear 1.0 bar

Starting the engine

 Sit in the driver seat.

 Set the gear lever to the neutral

setting N.

 Switch off the PTO-switch.

 Move throttle to maximum .

 Push the brake pedal down fully

or lock the parking brake.

 Turn the ignition key to /I.

Diesel motors have to be preheated

before starting the engine. Reaching

the required temperature for starting

the engine is indicated by the glow

plug pilot light going out.

Note

A warm engine does not need to be

preheated.

After the glow plug pilot light (A) has

gone out:

 Turn the ignition key to until

the engine runs. (max.10 sec. for

the first starting attempt). Wait for

one minute before the next

attempt, however at the same

time return the key to the /0

position.

When the engine is running:

 Turn the key back to /I.

 Slowly turn the throttle in the

direction /idle. Let the engine

run warm for approx. 3–5

minutes.

Note

Do not operate the engine when fully

loaded until it is has heated up.

For temperatures under 0 °C:

– Observe the correct viscosity of the

engine oil (see table in section “Ser-

vicing” and/or the engine manual).

– Set the throttle lever into

position .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 6000 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info